齿轮

In most passenger cars this allows the pinion to be offset to the bottom of the crown wheel.

在大多数轿车这使得小齿轮以抵消对冠轮的底部。

The absolut measure metheod was used as the basic principle of device building and software design of the ultraprecision gears total cumulative pitch error measurement system.

同时，遵循测量原理并采用高精度的元器件搭建了绝对测量法检测超精密齿轮齿距偏差的测量平台。

This paper discussed several methods of the evaluation on total cumulative pitch error of gear: diagram, tabulation, coordinate conversion.

齿距累积误差是影响齿轮传动准确性的重要检测项目之一，利用计算机方便、快捷地处理测量数据在工程中具有实际意义。

The chapter 7 introduces 3 kinds of sensor and instruments used for hydraulic system monitoring and fault diagnosis, they are eddy current sensor, gear-motor flow meter and portable pressure wave sampler.

第七章介绍了3种与液压系统的测试、分析和故障诊断有关的仪器，包括：电涡流式传感器、齿轮马达流量计和便携式流体压力波形采集仪。

During the procedure, the design of grip and cutter is also important.

在齿轮加工过程中，刀具及夹具的设计也尤为重要。

By considering torque characteristics of variable-frequency motors and mesh stiffness as well as backlash nonlinearity in gear transmission,a dynamics model for the cutting system of shield tunneling machine with redundant drives was established. The fluctuation characteristics of torque loads and dynamic cutterhead driving torque in composite strata were analyzed.

复合地层掘进扭矩载荷突变是造成盾构机掘进过程中堵转停机的直接原因，考虑盾构机刀盘驱动变频调速电机特性、转矩传递过程中齿轮啮合刚度及齿侧间隙等非线性因素，建立冗余驱动的盾构机刀盘切削系统机电耦合动力学模型；针对典型复合地层地质条件，对盾构机在上软下硬地层掘进过程中刀盘驱动转矩动态特性进行仿真分析。

For Gear Ratio DTC's, check and record all CVI's.

对于齿轮比 DTC 、检查和记录所有的 CVI。

The cyclic symmetric conditions of node points are presented to modify the stiffness and mass matrices of the substructure.With the use of the structural cyclic symmetry and the complex constraint conditions,the eigenvalue ...

这证明复约束法既极大地减少了计算所需内存和机时，又可建立包含轮齿和轮体在内的计算模型，保证了齿轮结构特征值问题计算的完整性和准确性。

Years of design and production of various generic reducer and micro-reducer, gear,-cycloid and other mechanical products.

多年设计生产各种通用减速机及微型减速机、齿轮、摆线针轮及其他机械产品。

Cyclodrive ; envelopment ; gears ; engage ; development ; cycloidal curve ; equidistant curves ; conjugate curves ; pitch point ; short arm coefficient ; planetary gear mechanism

摆线针齿传动；包络；齿轮；啮合；研制；摆线；等距曲线；共轭曲线；节点；短幅系数；行星机构

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。