齿轮

Lubricating oil pump gear wear mainly tooth thickness at the site, and the gear tooth face and the top are relatively light wear.

润滑油泵齿轮磨损主要是在齿厚部位，而齿轮端面和齿顶的磨损都相对较轻。

It is compared with involute gear most prominent advantage is that the process of meshing gear tooth profile surface there is no relative sliding, so no tooth wear, smooth operation, without the phenomenon of trapped liquid, low noise, long life and high efficiency.

它与渐开线齿轮相比最突出的优点是齿轮啮合过程中齿廓面没有相对滑动，所以齿面无磨损，运转平稳，无困液现象，噪音低、寿命长、效率高。

A toothed wheel that engages another toothed mechanism in order to change the speed or direction of transmitted motion.

一个齿轮咬住另一个齿轮为了改变传动装置的方向和速度。

The results show the speed reducer of trochoidal gears is much superior to that of involute gears of the same parameter in contact strength and bearing capacity as well as in wearing capacity and noise decrement.

证明了变长线齿轮减速器比同参数的渐开线齿轮减速器在接触强度、承载能力、噪音和耐磨性等方面具有较大的优越性。

In this article , instead of changing the ubiety among the parts of the original elevator , the author keeps on using the original structure. However, because of the differences of the transmission ratio and speed, the author enlarges the planet gear, solar gear , thickness of the inner circle ring as well as the enclasping radius of the enclasping brake through the mechanical design and calculation .

在设计过程没有改变原有的升降机零部件的位置关系，但由于，传动比以及传动速度的不同，所以，通过受力分析计算，加大了行星齿轮、中心齿轮、内齿圈的厚度；同时也加大了抱闸抱紧时的抱紧半径。

In this article , instead of changing the ubiety among the parts of the original elevator , the author keeps on using the original structure. However, because of the differences of the transmission ratio and speed, the author enlarges the planet gear, solar gear , thickness of the inner circle ring as well as the encl ASP ing radius of the enclASPing brake through the mechanical design and calculation .

在设计过程没有改变原有的升降机零部件的位置关系，但由于，传动比以及传动速度的不同，所以，通过受力分析计算，加大了行星齿轮、中心齿轮、内齿圈的厚度；同时也加大了抱闸抱紧时的抱紧半径。

The main production techniques and trail-manufacture of alloyed Aaustempered Ductile Iron and unalloyed ADI gears are introduced.

介绍了等温淬火球铁齿轮的主要生产工艺，以及合金与非合金等温淬火球铁齿轮的试制应用。

If the dial indicator reads 0.14~0.3mm , it means the tooth clearance is right; You can also use a 15~20mm long and 0.5mm thick lead sheet or "∽"-shaped fuse . Put the sheet or fuse between the unengaged tooth flanks tha is between the convex surface of small bevel gear and the concave surface of the large bevel gear. Turn the gear, then the pressed thickness of the big lead sheet end suggests the normal tooth clearance of this site.

另一种方法是用长15~20毫米，厚0.5毫米的铅片或弯成"∽"形的保险丝，放入两齿轮非啮合的齿面之间（即小锥齿轮的凸面和大锥齿轮的凹面之间），转动齿轮，则铅片在靠近大端处被挤压的厚度即为该处的法向齿侧间隙。

Each gear functions unintelligently and only in relation to other adjacent gears.

每个齿轮机械的运转并且只与其他相邻的齿轮有关系。

While one controls the upshift to the next gear, the other pack is disengaging the previous gear, for a near seamless transition.

虽然有一个控制upshift下一个齿轮，其他Pack是脱离前齿轮，为不久的无缝过渡。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。