齿轮

By applying the optimal tool parameters, the maximum tooth contact pressure is reduced by 45% and the maximum angular position error of the driven gear by 60%, in regard to the spiral bevel gear pair with a pinion manufactured by a cutter of straight-sided prole and of diameter determined by the commonly used methods.

通过应用参数的最佳工具，最大齿接触压力减少了45％，而最高的从动齿轮角位置误差60％，在关于由一个螺旋直齿轮刀具制造了一对锥齿轮双面形象和所常用的方法确定的直径。

Experimental results show these proposed methods, which can protrude the sideband structure of gear, are practical in gear fault diagnosis and of application and more thorough research value.

实验数据的分析结果表明这些方法可突出齿轮的边频带结构，适用于齿轮的局部故障诊断，具有一定的应用价值和更深入的研究价值。

Now the studs are mounted. Only the ratchet wheel is to be added.

O7 ~现在齿轮已经装配好了，只有棘齿轮没有加上

It is connected to the compact K2 clutch, which is integrated into the inside of its larger sibling, and which controls the gear wheels for gears 2, 4 and 6, as well as reverse gear.

它是连接到紧凑幼离合器，并把其内部集成更大的兄弟姐妹，并控制齿轮的齿轮2，4和6，以及倒档。

Use reverse Our sidecar have two style reverse gear box:the 52 style and 331 style,now I show you hao to use the 52 style reverse gear box.

使用侧扭转我们有两个风格扭转齿轮箱： 52式和331式的，现在我告诉你浩使用的52式反向齿轮箱。

The radial power of each of inner gear of transmission ring which works on output shaft is zero.

每一组传动环板的内齿轮对外齿轮的径向作用力的合力为0。

Note that the input pinion is a smaller gear than the ring gear.

注意到主动齿轮的齿数比冠状齿轮少。

Inside each gearbox, a pinion gear spins a ring gear attached to ball diff.

变速箱内的每一个齿轮旋转的齿轮一齿圈重视球差异。

The results indicated that the gears designed by this method have a basically similar performance to the tested results of the long-tooth gears in an imported roller mill.

结果表明，采用本方法所设计的齿轮，与进口辊式磨粉机上所采用的长齿齿轮的实测结果基本一致。

Firstly,using the method of concentrate mass this paper establish a non-linear dynamics model of a two-stage gear train with backlashe between the gear pair,and through analysed the dynamics model,the torsional motion differential equations are got , on this basis,then calculate the torsional motion differential equations using Runge—Kutta method ,and discuss how to influence the dynamics characteristic of system when these parameters chage such as mesh frequentcies、 stiffness of the intermediate shaft、the ration of mesh frequentcies.and discuss when the chaos will happen under the change of these parameters.

首先用集中质量法建立系统的含间隙的非线性动力学模型，并根据牛顿力学定理，得到系统的运动微分方程。然后对所建立的运动微分方程运用四阶变步长Runge—Kutta方法进行了求解，并对计算结果进行分析，研究了齿轮啮合频率、中间联接轴的刚度，一、二级齿轮的啮合频率比等参数变化时，对系统非线性动力学特性的影响规律，并讨论了当参数如何变化时会导致系统的混沌响应的出现。

The concept of equivalent rotationally rigidity is offered and the formula of rotationally rigidity is obtained.

主要做了如下几个方面的工作：对伸臂位于顶部的单层框架—筒体模型进行分析，提出了等效转动约束的概念和转动约束刚度的表达式。

Male cats normally do not need aftercare with the exception of the night after the anesthetic.

男猫通常不需要善后除了晚上的麻醉。