齿轮

The drawback with GB3480-83 Methods for the calculation of load capacity of involute cylindrical gears equivalent to ISO/DP6336/I∽III-1980 is also pointed out: when taking into account lubricating state of gear surface influence on loading capacity of gear surface, In the above it is study on based EHL , and is ignored that in the state of boundary lubricating, as well as favorableness conditions in gear surface conjugate meshing, the active atom resolved from the additive permeates the surface and forms the modifying layer totally different from its basic structure, elements and function and thus greatly raises the loading capacity of gear surface .

也指出了等效于ISO/DP6336/Ⅰ∽Ⅲ-1980的《GB3480-83渐开线圆柱齿轮承载能力计算方法》的缺陷：在考虑齿面间润滑状态对齿面接触强度承载能力影响时，是以弹性流体动力润滑理论为讨论问题的基础，未考虑边界润滑状态下，非活性润滑油抗磨添加剂在啮合过程中，由于各种有利因素会分解出活性原子，渗进齿轮表面，形成表面改性层，极大的提高了其承载能力。

The billets flowing is very complex during forming process, and it has multi factors which can influence figuration and precision of the spur gear.

直齿轮的冷锻成形，属于复杂的三维变形，金属坯料在成形过程中的流动十分复杂，有多种因素影响齿轮的成形和精度。

This design wants to design a complete set of three axes five speed gearboxeses , it mainly include three parts : The first part , to make sure the basic parameter of the gearbox assurance ; The second part, The contact strength verify-check and the flection strength verify-check of each wheel gear of the gearbox, mainly verify whether each wheel gear satisfy various strength conditions with according to the giving parameter ; The third part , to progress verify-check intension of the axes Four-part cent, to calculate the life of the bearings.

本次设计是要设计一部较为完整的五档变速器，其中主要包括三部分：第一部分，变速器基本参数的确定；第二部分，变速器的各档齿轮的接触强度校核和弯曲强度校核，主要是根据所给的参数来验证各档齿轮是否满足各项强度条件；第三部分，进行轴的强度校核；第四部分，轴承的寿命计算。

This article first determines major component's structure pattern and the main design variable; Then the reference similar driving axle's structure, determines the overall project design; Finally to the host, the driven bevel gear, the differential device circular cone planet gear, the rear axle shaft gear, the full floating axle and the integral-type bridge shell's intensity carried on the examination as well as has carried on the life examination to the supporting bearing.

本文首先确定主要部件的结构型式和主要设计参数；然后参考类似驱动桥的结构，确定出总体设计方案；最后对主，从动锥齿轮，差速器圆锥行星齿轮，半轴齿轮，全浮式半轴和整体式桥壳的强度进行校核以及对支承轴承进行了寿命校核。

We have made a long term business relationship with Shanghai General Automobile Gears Manufacturers , JiangSu Flying Boat Gears Joint-stock Company Ltd., Yuejing Group, Jiangling Automobile Group and China Heavy Duty automobile Group etc.

经过短短几年的发展，公司现已成为华东地区锻造行业的后起之秀。公司与上汽集团齿轮总厂、江苏飞船齿轮股份有限公司、跃进集团、江铃汽车集团、中国重汽集团等国内知名企业保持常年协作关系。

In the second test, the frequency response function is measured and the primary natural frequency has been obtained.

前者研究了不同转速下行星齿轮动态响应的频谱特性，后者则给出了行星齿轮传动的固有频率。

That the curves of the normal force and friction force between two corresponding gear teeth in a given condition can supervise the design and optimization of gear system.

得到了某一特定传动条件下单对齿轮轮齿法向力及齿间摩擦力的变化规律曲线，从而可以指导齿轮系统的设计和优化。

Based on the measurement of noise of an idling lathe C630,the effects of gear tooth friction on change gear noise ,and the relation between friction excitation frequency and gearing frequency were analyzed.

结果证明：齿面摩擦对齿轮振动的激励频率是啮合频率的2倍，可以利用适当的润滑有效地抑制齿轮噪声的高频成分。

The main identifying characters of wear particle on the ferrogram such as dimension,distribution,quality,component and form of the wear particle were generalized for the three friction couples of gear case including gear,bearing and sliding contact which is in the different phases of running-in wear,normal wear and abnormal wear and in the different degrees of overload,over-speed and fatigue.

介绍了铁谱分析的原理、样品的制备方法和铁谱分析的步骤，概括了齿轮箱齿轮、滚动轴承、滑动接触3种主要摩擦副在磨合磨损、正常磨损、异常磨损3个阶段的磨粒的主要识别特征，包括尺寸、尺寸分布、数量、成分和形貌等。

Besides this, we have studied the special function and significance of impulse vibration signal in the gear case's malfunction diagnose.

承、齿轮、轴系三类零件各自的故障特征信号，同时研究冲击振动信号在齿轮箱故障诊断中的特殊作用和意义。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。