齿轮

These approaches are suitable for noncircular gear not only with discontinuous pitch curve but also with continuous pitch curve.

这一方法不仅适用于节曲线不连续的非圆齿轮设计，对节曲线连续的非圆齿轮设计也同样适用。

Thus, it is of great theoretic and realistic significance to research on correlative technology of gears.

因此，研究齿轮及齿轮加工的相关技术具有很大的理论和现实意义。

Later, with the application of gears, two cotton gin with a pair of roller blades to replace the original gear ...

后来，随着齿轮的应用，轧棉机的两个压辊采用一对齿轮。。。

When none of the sliding gears is in mesh with its countershaft gear, the gears are said to be in neutral.

如果没有变速齿轮组与副传动轴上的齿轮啮合，这时，就叫做空挡。

Reverse speed is obtained by the use of a small/pinion R between the countershaft gear I and the sliding gear K, which causes the transmission drive shaft to be driven in the opposite direction.

相反速度被在对桥之间的小/鸟翼 R 的使用获得以齿轮连起我和滑齿轮 K，引起传输驱动轴在相反的方向中被驱使。

Our production receives a great honor in internal craft brother and extensive automobile users.

建立先进的齿轮生产线在显示企业雄厚的实力的同时，齿轮质量大大提高，产品在国内同行和广大汽车用户中享有较高的声誉。

The transmission properties of crown gear coupling are analyzed comprehensively. The crowning curve and the gear parameters are optimized.

本文较全面地分析了鼓形齿联轴器的传动特性，提出了鼓形齿轮鼓度曲线及齿轮参数优化设计新方案。

A simple and practical method to reequip the hobbing machine by using CNC system to machine the crown gears is introduced. It has advantages of high machining quality and efficiency, high stability and reliability, simple operation, good adaptability to different lots, easy to realize, low cost and high benefit. It is an economical and efficient technique to machine crown gear. It is of particular extending value, meeting the domestic needs of crown gear coupling manufacturing.

介绍了一种新开发出的简单实用的数控化改造普通滚齿机加工鼓形齿轮的方法，它具有加工质量好、生产效率高、系统稳定可靠、操作简单、产品批量适应性强、改造容易实现、改造成本低、效益高等优点，是一项经济有效的鼓形齿轮加工技术，适合现阶段国内鼓形齿联轴器制造的要求，具有较高的推广应用价值。

The aim of the subject is to design and check the strength of the gears of crown gear coupling from the Beijing subway and to analyse the teeth by means of 3D FE elastic contact method. The result can numerically and theoretical support the design and manufacture of crown gear coupling.

本课题研究的目的是通过对北京地铁联轴器齿轮副进行强度设计和校核，并且对其进行三维弹性接触有限元分析，得出鼓形齿联轴器齿轮副的弹性接触状况，为鼓形齿联轴器的设计及制造提供数据和理论支持。

At last, the factors affecting pitch measurement accuracy of Marh891E Gear measurement center was analyzed; the hardware and the software of the ultra-precision gear total cumulative pitch error measurement device were improved, which perfected measurement system and increased the measurement efficiency and accuracy.

本文最后分析了Marh891E齿轮测量中心上、下顶尖不同轴对被测件齿距精度的影响，并通过具体分析对其进行调整；对超精密齿轮齿距累积总偏差测量装置的硬件控制部分及软件部分做了改进，完善测量系统，提高检测效率和精度。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。