齿轮

AMM provides a full casting service for gears and pinions and also non-standard parts.

东盟提供了一个充分铸造服务齿轮和小齿轮，也非标准件。

The force analysis models and the analytic solutions of the type transformation units of the geared linkage mechanism were given, the forceanalysis models were perfected.

给出了齿轮连杆机构型转化法力分析单元的模型及显式解，完善了齿轮连杆机构力分析的数学模型。

It comprises an in-put shaft hinged to its yoke through one axis, and an out-put shaft also hinged to its yoke through another axis, and these two yokes (13) were combined together by only one axis position, perpendicular to that two yoke axes like a cross, so that this combined axis will bend just like the angle bisector of that two shafts to maintain its constant velocity by a few methods, firstly, by using a section of gear teeth mesh at both ends of the shafts' teeth were so polished so that it can turn longitudinally as usual gear, and also sideways, to provide a larger solid angle of turning from ordinary 45 degrees into 60 or even more.

它包括输入轴，其通过一根轴铰链连接于叉形支架，和输出轴，其通过另一根轴也铰链连接于其叉形支架。并且这两个叉形支架(13)只需用一根相对垂直铰链轴相连而组合在一起，使得这种组合的轴总能形成这两个轴的角平分线，以通过少数几种方法保持其恒速，首先，通过用啮合在轴的两端的一段齿轮齿抛光为以能够像普通齿轮一样纵向转动，并且还能够侧向转动，以提供较大的转向立体角，从通常的45度变成60度或更大。

In spur gears the line of contact is parallel to the axis of the rotation; in helical gears, the line is diagonal across the face of the tooth.

在正齿轮联络线与自转的轴是平行的；在螺线齿轮，线横跨牙的面孔是对角的。

According to the experience formula, the axle of the gear wheel has been used in the design of mechanical construction.

根据经验公式计算，在齿轮传动链的设计中齿轮需要采用齿轮轴的形式。

In the fourth chapter, all the calculating equations of fault vibration frequency of gear shafting components of gear unit are summarized and the calculating equations of fault vibration fiequency of commonly used barrel-shaped roller bearing are deducted.

另外，为了防止齿轮减速机在工作时发生突发性事故和更好地延长齿轮轴系部件的寿命，需对具体的齿轮减速机设备进行在线监测和智能故障诊断方面的研究。

At the same mesh point, the bending stress on the gear is bigger than that on the pinion.

对于同一啮合点，凹齿轮齿根应力大于凸齿轮的齿根应力。

You can fit up to 143 teeth between the pinion and spur with 64P gears.

您可以容纳143牙齿之间的齿轮和鞭策与64P齿轮。

When gears are to be used to transmit motion between intersecting shaft, some of bevel gear is required.

当齿轮是用来传递运动之间的交叉轴，其中有些圆锥齿轮的需要。

The factory bevel gear production, transmission gear of all types have years of experience, is a senior in research, development, design, manufacture, sales, service as one of the company.

本厂生产伞齿轮，齿轮各类传动件已有多年的经验，是一家资深的从事研发、设计、制造、销售，服务为一体的公司。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。