齿形

Every now and again someone will notice the gears on one of my SOG tools. They'll usually ask what they're for and I'll try to explain the gear-drive and compound leverage before their eyes glaze over and they stop caring.

很多次朋友都会注意到我的SOG工具上的齿形结构，他们总会问这个干什么的，而我也不厌其烦的向他们解释这个是齿形同步和复合杠杆结构。

Much attention is paid to the mesh principle of variable ratio rack and sector, which includes the principle of variable ratio, the selection of gear type, the setting up of rolling pitch line, and the determination of tooth profile.

重点说明转向器中变速比扇形齿轮和齿条的啮合原理，包括变速原理，变速齿轮的选择，滚动节线的建立，齿形的确定等问题。

IPOs coat of arms of the Republic of China on the national flag stamp self adhesive 试制品 unladed pond?athis dentiform detailed comparison, and traditional stamps as fine hole teeth.

此次发行的《中华人民共和国国旗国徽》邮票不干胶试制品种即采用了比较细密的齿形，和传统邮票孔齿一样精细美观。

Having the form of a tooth; toothlike.

齿形的；象齿的

The change of center distance due to non-conjugate of corrugating roller in molding corrugated board process was discussed.

论述了瓦楞辊在成型瓦楞纸板过程中，由于瓦楞辊的齿形是非共轭齿廓，中心距是变动的。

By using hyperbolas to fit axial curves, considering the maximal error of the fitting curves as the objective function, the optimal fitting hyperb...

通过双曲线来拟合齿向曲线，使拟合曲线的最大误差为目标函数，利用优化的方法，使最大误差最小，得到最优的拟合双曲线，从而加工出所需要的齿形。

By using hyperbolas to fit axial curves, considering the maximal error of the fitting curves as the objective function, the optimal fitting hyperbola is obtained and the maximal error of fitting curves is minimal after optimization.

通过双曲线来拟合齿向曲线，使拟合曲线的最大误差为目标函数，利用优化的方法，使最大误差最小，得到最优的拟合双曲线，从而加工出所需要的齿形。

Then according to some inputted basic parameters of gear, the paper calculates the geometry dimension of the transmission gear.

然后根据输入的一些齿形基本参数，计算得到变速器齿轮齿廓的相关几何尺寸。

The engagement theory of the gear rack mechanism can be used to study the silent chain mechanism.

基于齿轮齿条机构的啮合理论，研究了渐开线齿形链机构的啮合机理。

The selection rules for the angles of jaw clutch, the determination of the sup ply voltage for the magnet, the design of the control circuit to eliminate the so-called "striking jaw top" and the measures to reduce residual magnetism and the switching time are discussed. The code circuit designing method for the speed control of the spindle box in XHK 5140 machining centre is also described.

本文根据牙嵌式电磁离合器的使用情况，对离合器齿形角的选择原则、激磁电压的设计、消除顶齿的控制电路的设计，以及采用电容器放电消除剩磁和缩短断开时间等问题进行了讨论，最后介绍了XHK5140立式加工中心主轴用电磁离合器变速的译码电路的设计方法。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。