高速度

The results show that laser cutting of sandwich material need higher power, gas pressure, lower speed than common steel.

结果表明；与普通钢相比，三明治材料的激光切割需要更高的功率、气体压力、较小的速度。

Many consider him to be one of the best leadoff hitters of the 1980s and early 1990s, due to his high on-base percentage, speed and dynamic bunting.

拥有速度，高上垒率与不错短打能力的Butler被许多人认为是1980年代至1990年代早期最佳的第一棒打者。

As an example, using the standard AMR-NB (Adaptive Multi Rate compression, narrow band) vocoder C reference, the CEVA-X1622 DSP core required just 19 MHz when compiled out-of-the-box (for worst-case frames and streams). In comparison, other licensable solutions require more than 45% higher speed for the same out-of-the-box compiled code.

以使用标准窄带自我调整多速率压缩的C语言语音编码器为例，CEVA-X1622 DSP内核在编译现成可用的代码时，仅需19 MHz速率；而其它可授权解决方案却需要高百分之四十五以上的速度，才能编译同样的现成代码。

This harness and life preserver combination is designed for higher ejection speeds than those used in other aircraft," Merrill notes."

这种降落伞装具和救生设备的组合是针对比其它飞机所拥有的更高的弹射速度设计的，"米勒上校解释说。"

With application of plastic limit analysis method using finite element method, stability of high loess slope is analyzed and solved by using linear programming method in this paper. Safety factor and stress fields and velocity fields of slope can be obtained.

本论文采用有限元塑性极限分析法对黄土高边坡进行稳定分析，并运用线性规划的方法对稳定问题进行求解，可以得到边坡的稳定安全系数和边坡的应力场及速度场。

Advantages such as high production ability fast reaction velocity and low exhaustion are also proved in research.So it is one of the most advanced technology of hematite、siderite and limonite magnetizing roasting.

该工艺具有单位体积产能高，反应速度快，能耗低等优点，是赤铁矿、褐铁矿、菱铁矿磁化焙烧的先进工艺。

The interferometer is not only used in measuring linear displacement and linear velocity, but also in measuring small angles, form and position errors.

随着世界工业的迅猛发展，人们对位移测量、定位、标定的精度和测量速度提出愈来愈高的要求。

If you are right, you should hire the looker as lookers are easier to have around.

他们的薪水会高出15%，而且升迁的速度更快。

It is necessary to distinguish the loss leader from the normal pricing of a highelasticity, stronglybran...

对反托拉斯当局来讲，严格区分亏损诱饵和高弹性商品、知名品牌以及销售速度较快产品的正常价格是必要的。

The results prove that using the laser power P=1.7Kw, scanning velocity V=4mm/s, spot diameter D=3mm, cladding thickness T=0.6mm, 50%: 50% Ni60:Ni-Cr-Cr_3C_2 as laser cladding process can obtain the laser coating with lubricous tight surface, tiny dilution rate ,fining microstructure and higher micro hardness and fine metallurgical-bonding Interface.

试验结果最终证明，激光熔覆工艺参数对熔覆层的宏观形貌、微观组织及涂层性能有极大的影响，在激光熔覆工艺参数为功率P=7Kw，速度Vs=5mm/S光斑直径D=3mm，厚度T=0.6mm，50%；50%的Ni60；Ni-Cr-Cr_3C_2的条件下，所得到熔覆层表面光滑致密、组织细小均匀、稀释率小、硬度高且与基体实现了良好的冶金结合，证明这种方法是一种在提高热锻模寿命方面有前途的方法。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。