验证试验

45C Are independent tests carried out to validate the results?

为了对设计进行验证，是否进行独立的试验？

Being aiming at the knowledge of image model matching, it adopts single meme and real code. It puts out fast co-evolution matching algorithm strategy. Basing on NPROD resemble measurement, I emulate the indiscrimination model matching and discrimination model matching. Finally, it valuates the co-evolution algorithm's efficiency on the real code and real time search issue.

针对图像模板匹配问题的领域知识，采用单类拟子和实数编码，给出快速共同进化匹配算法策略，基于NPROD相似度测度，仿真试验了无差别和有差别模板匹配，验证了共同进化算法对实数编码和实时性搜索问题上的有效性。

In order to make it, some change on engine inlet system have been adopted.

在以前的研究工作基础上，为提高发动机的动力性，主要对进气系统进行了改进，并通过气道试验加以验证。

Finally, the paper compares the test result of model experiment with the calculating result of the paper, they inosculate well each other.

最后，用钢箱索梁模型试验的测试结果验证本文的理论计算值，分析结果是比较吻合的。

According to the theories of dynamics of explosive and rock fracture mechanics, initiation mechanism of kerf, and initiation of crack in its tip and its expansion of orientation fracture blasing with slit-charge in rock were studied, then the blasting, parameters were designed and tested by model test in laboratory.

以爆炸力学、岩石断裂力学理论为原理，对切缝药包在岩石定向断裂爆破中的切缝产生及裂纹起裂和扩展进行了一定的研究，同时对该法的爆破参数进行了设计，并在实验室进行模型试验验证其正确性。

Then the model of the fifth scheme is determined to be the best one by comparison of each with other and then this model is applied to actual production of ladle.

然后将第5种方案的模型应用到钢包的实际生产中，现场使用表明钢包的寿命得到了很大的提高，用试验对第5种方案的模型进行了验证。

Through load and curve tests,its feasibility got the confirmation.

通过负载试验和波形测试，验证了设计的可行性。

In the dissertation, a dynamic model has been established for a torque converter with lock-up function.

本文还建立了闭锁式液力变矩器的力学模型，进行了液力变矩器闭解锁过程动态性能模拟和分析，对部分模拟结果作了试验验证。

For the sake of investigate the connection between segregator effect and its configuration parameters, operating status, based on predigest in reason, a test-bed is built to experiment and analyze the current of segregator effect as the intake wind speed and the internal longness of the outlet pipe change.

为了研究分离器效率与其结构参数以及运行条件的影响关系，在合理相似简化的基础上，设计搭建一个冷态试验台，在现有的条件下对分离器效率随入口风速以及内筒插入深度的变化趋势进行试验和分析，验证了相关的结论。

The numerical simulation results of the Lorenz system show the effectiveness of the proposed method.

数值仿真试验进一步验证了该方案可以实现Lorenz混沌系统的广义投影同步。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。