验证试验

By means of the self-designed equipment used for the interaction test of tread element with road surface, the contact behavior of tread element and the effects of the design parameters are studied for the first time in the domestic.

应用自行设计的胎面单元与路面相互作用试验装置，在国内首次研究了胎面单元的接地特性和设计参数对单元特性的影响，并以此对本文的数值研究结果作出验证。

And in the last part, the design is proved to be feasible by emulate and test.

最后，对系统进行了仿真及试验，验证了本设计的可行性。

In order to verify safety,efficiency and high quality of high-speed cutting machining,I d like to analyze the whole manufacturing process;from drawing up the steps of mould machining;taking rough machining,semi-finish machining and finish machining into account,and designing a reasonable machining scheme through emulation mode to meet the demand of high-speed cutting machining.

为了验证高速切削技术的安全、高效和高质量特性，从一个高速铣削加工任务开始，分析了高速加工模具工艺制订步骤，把粗加工、半精加工和精加工作为一个整体考虑，设计出合理的加工方案，通过仿真达到高速切削技术的要求，并通过实际加工，得出与传统工艺电火花线切割加工对比后的试验数据，论证了高速切削工艺的高效和经济性。

In chapter 2 we propose a linear equality constraint optimization question , the new algorithm is combined with the new conjugate gradient method(HS-DY conjugate gradient method)and Rosen"s gradient projection method , and has proven it"s convergence under the Wolfe line search.In chapter 3 we have combined a descent algorithm of constraint question with Rosen"s gradient projection, and proposed a linear equality constraint optimization question"s new algorithm, and proposed a combining algorithm about this algorithm, then we have proven their convergence under the Wolfe line search, and has performed the numerical experimentation.

在第三章中我们将无约束问题的一类下降算法与Rosen投影梯度法相结合，将其推广到线性等式约束最优化问题，提出了线性等式约束最优化问题的一类投影下降算法，并提出了基于这类算法的混合算法，在Wolfe线搜索下证明了这两类算法的收敛性，并通过数值试验验证了算法的有效性。

Simulation results show validity of the proposed method, and the equivalency of the four schemes is verified.

给出了基于所提算法和其它三种调制方法的四桥臂DC/AC逆变器的仿真试验结果，该结果显示了算法的正确性和有效性，验证了等效性的结论。

A functional relationship equation between the equivalent mass of the fruit and the A/D conversion result was achieved and calibrated with apples, and it was testified with other apples.

通过对质量不同的苹果进行实测标定，得出了等效质量与其A/D转换值之间的关系式，并进行了试验验证。

In order to simplify control parameters design, the modeling method of equivalent inductance is put forward and Validated by simulation and experimentation.

在此基础上为简化控制系统参数设计，利用等效电感建模法建立了调速系统在复频域内的动态数学模型，并进行了仿真和试验验证。

Uses MATLAB software to carry on the computation to 6×4 the contractor power efficiency,discovers automobile each related parameter to the power efficient influence rule,determined the influence power efficient various essential parameter,through adjusts each kind of correlation disposition to achieve improves the entire vehicle power efficient goal.

采用MATLAB软件对6×4重型牵引车的动力性经济性进行了计算，确定影响动力性经济性的各关键参数，通过调整各种相关配置达到改善整车动力性经济性的目的，并通过整车道路试验验证计算结果，采取优化措施改善整车的动力性经济性。

Metering application for review of assessment standards: measurement standard assessment the original of the application; standard measurement of the original assessment certificate; evaluation standard measurement certificate is valid within the standard set measurement device and the main equipment of a copy of the certificate; returns to replace the standard measurement; measurement Standard in the near future to carry out verification / calibration of the original records and test / calibration copy of the certificate; stability of the measurement standard evaluation copy of the record; measurement standard measurement repeatability evaluation copy of the record; measurement standards in the two-cycle test run between the inspection or verification Test copies of the records.

申请计量标准复查考核：计量标准考核申请书原件；计量标准考核证书原件；计量标准考核证书有效期内标准器及主要配套计量设备的检定证书复印件；计量标准更换申报表；计量标准近期开展检定/校准的原始记录和检定/校准证书复印件；计量标准稳定性考核记录复印件；计量标准测量重复性考核记录复印件；计量标准器在两周期检定之间进行运行检查或验证比对试验记录复印件。4。

An asynchronous staggered iteration FEM method with explicit difference scheme is suggested to solve solid-liquid coupling dynamic elastoplastic problem.

提出了一个新的次塑性模型并用试验作了初步验证，建议用异步交叉迭代显式差分有限元求解固液耦合动力弹塑性问题。

She gently rebuff ed him, but agreed that they could be friends

她婉言拒绝了，但同意作为朋友相处。

If in the penal farm, you were sure to be criticized.

要是在劳改农场，你等着挨绳子吧！