颈轴的

In rotational process, the rotor of journal bearing relies on the oily wedge that slippery oily oily film forms to poise, bearing gets power but the bedspring damp system that described as rotates.

转动过程中，轴颈轴承的转子依靠滑油油膜形成的油楔保持平衡，轴承受力可描述为旋转的弹簧阻尼系统。

The method can be used in test of multiplicate crankshaft with different neck sizes.

该方法可适用于多种轴颈尺寸的曲轴试验。

We also observed and measured the distance and section of some muscles such as long muscle of neck、long muscle of head、sternocleidomastoid、trapezius、longissimus、inultifidus、splenius、semispinal muscle of head、semispinal muscle of neck、anterior scalene、middle scalene 、posterior scalene et al. We achieved the moment of force and downloaded the force in the model .We also added gravity of head.

通过横截面积肌力计算法，测量尸体颈椎周围的主要肌肉：胸锁乳突肌、斜方肌、头长肌、颈长肌、肩胛提肌、夹肌、前斜角肌、中斜角肌、后斜角肌、多裂肌等的横截面积及其与颈椎纵轴的中心距数值，求得力矩值，直接或根据力矩等价公式间接的将肌力值加载于模型体表各点。

Surface morphology, microstructure and wear morphology of the coatings were investigated using model KYKY-2800 scanning electron microscope modeled. Phases of the coatings were analyzed using model D/max-RA X-ray diffractometer. Microhardness of the coatings was tested using model MH-6 hardness-testing device. The wear-resisting property of coatings was compared with 65Mn steel treated by the quenching and backfiring technology using the home-made abrasion machine. The feasibility was analyzed for reactive electric-spark build-up welding TiN cermet coating to be used for gear shaft restoration.

采用KYKY-2800型扫描电镜观察了堆焊层表面形貌、显微组织和磨损形貌，采用D/max-RA型X 射线衍射仪分析了堆焊层物相，采用MH-6型显微硬度计测定了堆焊层显微硬度，采用自制磨损实验机对比了堆焊层与淬火回火65 Mn钢的磨损性能，分析了电火花堆焊TiN金属陶瓷层用于轴颈修复的可行性。

The part of a machine shaft or axle supported by a bearing.

轴颈机械的转动轴或轮轴中由轴承所支撑的部分

A set of measurement system for bearing and axle journal on passenger car has been developed to fulfill the work of measuring the dimension,data saving,communication and data management,which overcomes disadvantage of manual measurement,such as low efficiencies,high cost,high labor intensity and low precision.

针对铁路客车轴承与轴颈人工测量效率低、成本高、劳动强度大、精度差等缺点，研制了一套客车轴承与轴颈尺寸的测量系统，能够完成尺寸的测量、数据存储、通信和管理工作。

The new technologies adopted in the design of φ1830mm 25 0mm dryer bearing assembly such as cone journal, CARB bearing, heat insulation sleeve and oil lubrication are introduced and the principle of lowering bearing temperature is discussed.

介绍在φ1830mm×6250mm烘缸轴承装置设计中采用的新技术，如锥颈轴、CARB轴承、隔热套、稀油润滑，同时探讨了降低轴承温度的原理。

The fluid-film size between the rotor and stator is 50μm, which can account for lubrication and journal bearing.

而介於定子与转子间的润滑薄层为50μm，且能产生润滑及轴颈轴承的作用。

"The four arms of the spider, known as trunnions, are assembled into bearings in the ends of the two shaft yokes."

万向节十字轴的四个轴颈叫做万向节十字头，分别装在两个万向节叉顶端的轴承中。

"The four arms of the spider, known as trunnions, are assemble d into bearings in the ends of the two shaft yokes."

万向节十字轴的四个轴颈叫做万向节十字头，分别装在两个万向节叉顶端的轴承中。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。