预热

The RTS profile generally will result in brighter and shinier joints and fewer problems concerning solderability, since the solder paste reflowed in a RTS profile will still contain its flux vehicle throughout the entirety of the preheat stage.

在 RTS 曲线中，锡膏中的助焊剂媒介在整个预热过程中的存在，会促进焊料的润湿，因此 RTS 曲线可以用难以焊接的合金和元件上。

Putting the contaminated scrap into the bath directly without preheating and pyrolysing will increase the metal loss by oxidation, because the contaminants are containing oxygen, which will react with liquid aluminium immediately.

将含杂质的废铝在未经预热和热分解的情况下直接加入到熔池中会增加金属的氧化损失。因为杂质中含氧，直接加入到铝液中，会立刻与铝液发生反应。

Results showed that the temperature in the fluidized bed was steady under the condition of adopting the plasma body to heat the reactor,and the preheat time is 1.5 h.

结果表明采用等离子体加热，整个反应器的预热时间大约为1.5 h，且反应过程中流化床内温度稳定，有利于生物质快速热裂解反应的进行。

Theory structure is presented in this paper about press plate wood vacuum dryer, and model of theoretical preheating time is built related to wood vacuum drying technology.

本文对压板式木材真空干燥机进行了结构介绍，以模型的形式确立了木材真空干燥工艺的理论预热时间，并以ZKY-01型箱式木材真空干燥机为试验仪器，采用波动压力方法对柞木和柯木进行真空干燥工艺试验。

This paper address the preliminary knowledge about sateflow and the modeling method about safety interlocking loop base on sateflow and farther expatiate it with a example of prewarming burner of alumina hydrate furnace.

本文介绍了Stateflow的基础知识以及基于Stateflow的安全联锁回路仿真建模方法，并以氢氧化铝焙烧炉预热燃烧器作为具体实例进一步阐述。

They applied many kinds of forms network: plane media, the color spurts, Banners, playbills and so on.

应用网络，平面媒体，彩喷，横幅，海报等多种形式，用强大的宣传攻势，为活动的开展起了很好的预热作用。

Sliding knobs at the left side of the press with steel scale in mm to set the opening distance of the platens during preheating and venting.

压机左侧有滑动旋钮，上面带有精确到毫米的钢刻度，可用于设定压台在预热和排气时打开的距离。

Cut the phyllo layers into 10cm triangles. Arrange on a baking sheet sprinkled lightly with flour. Bake in a preheated 180°C oven until golden brown and crisp. Remove and let cool immediately.

将饼皮切成10厘米三角形，排在已撒上少许面粉的盘上，放摄氏180oC预热焗炉内焗至金黄色酥皮，取出待凉透。

The processes of preheating and welding of super scale penstocks were detailed.

本文详细叙述了巨型压力钢管的预热装配和焊接过程。

The research work of KPG and Agfa has been reviewed in detail c overing both negative thermosensitive plates and positive thermosensitiv e plates.

从阴图热敏CTP版和阳图热敏CTP版两个角度对KPG和Agfa两公司的研究内容进行了详细总结，指出其中无预热和免处理热敏版是今后热敏CTP版材研究开发的方向。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。