预热

To enhance images, the plate is then fed into the warning to the processor unit, which will increase the energy of molecules, and have more monosomic cross-linking reaction occurs, the goal is to create long, as many as possible of the chain because the chain for the coating to provide hardness of preferences, and will affect the printed version in the business card printing machines have their life.

为了放松影像，印版置入到冲刷机的预热单位，这不兵为分子补充能量，并让单体爆发更众交联不正响，其纲的是创设尽不定不幼、尽不定众的链，因为链是为涂层供答硬量的不主给成分，并会感化印版在制卡机上的寿命。

The process of establishing neural network is as follows: two-layer neuronic network configuration is selected, S-type active function is used, input parameter of network are selected for thickness, preheat temperature, heat input and sampling point, output parameter of network is selected for fracture toughness property CTOD, learning algorithm of network is used for back-propagation algorithm.

本文选择了2层神经元的神经网络结构，采用S型激活函数，将板厚、预热温度、线能量、取样位置作为神经网络的输入，将环焊接头的裂纹尖端张开位移CTOD值作为网络的输出，通过BP算法的网络学习，采用VC语言建立了X70管线钢环焊接头CTOD与环焊工艺之间的神经网络。

The process of establishing neural network is as follows: input parameters of network are selected from thickness, preheat temperature, heat input, welding position and sampling point, output parameter of network is impact ductility CVN, two-layer neuronic network configuration, S-type active function and back-propagation learning algorithm are selected.

文章摘要：采用VC语言实现了X70管线钢环焊接头冲击韧性与环焊工艺之间神经网络结构的建立过程，将壁厚、预热温度、线能量、焊接位置、取样位置作为结构的输入，将环焊接头的CVN值作为结构的输出，选择了具有2层神经元的神经网络结构和S型激活函数及BP学习算法。

The test result showed that the pour point of Jianghan crude oil might depress from 28 ℃ to 13 ℃ when styrene∶maleic anhydride∶octadecyl acrylater was 1∶3∶3, preheated temperature of the crude oil was 60 ℃, and addition of the terpolymer was 300 mg/L.

研究表明，当苯乙烯、马来酸酐、丙烯酸十八烷基酯三种单体摩尔比为1∶3∶3，原油预热温度为60 ℃，三元共聚物在江汉原油中加量为300 mg/L时，此三元共聚物可使江汉原油的凝固点从28 ℃降到13 ℃。

3Through the result of orthographical experiment, the optimum processing is that the initial moisture content of fiber was 11%;the time of microwave heating was 100s;the height of mat was controlled in 3cm and the hot pressing time was 5min.

3筛选出正交试验的最佳工艺条件为：板坯初含水率为11%，微波预热时间为100s，板坯预压高度控制在3cm，热压时间为5min 。

The system can monitor on line operation state of the boiler system, including overall monitor of the boiler system, major monitor of boiler, run tending monitor, bar figure display and overrange alarm.

故障诊断根据锅炉运行状态监测情况，确定锅炉系统运行中出现的故障征兆，采用深、浅知识相结合的混合诊断推理机制，分析诊断锅炉系统在运行过程中可能出现的各种故障，如炉膛灭火，过热器爆管，省煤器磨损、泄漏，空气预热器积灰、泄漏，锅炉满水、缺水等常见故障。

The optimal production conditions are as follows: liquid paraffine warm-up temperature 80℃,reaction temperature 80~100℃,chlorine flow rate 80~100m3\h,reacting time 5.5~6.5h, adding 0.03% catalyst , 0.3% additive and 0.15% stabilizer .

确定了最佳的工艺条件：液蜡预热温度80℃，反应温度80~100℃，氯气流量80~100m3\h，催化剂用量0.03%，添加剂A用量0.3%，反应时间5.5~6.5h，稳定剂用量0.15%。

The optimal production conditions are as follows: liquid paraffine warm-up temperature 80℃,reaction temperature 80~100℃,chlorine flow rate 80~100m3/h,reacting time 5.5~6.5h, adding 0.03% catalyst , 0.3% additive and 0.15% stabilizer.

对低正构烷烃液体石蜡生产合格的氯化石蜡提出内稳定设想，确定了最佳的工艺条件：液蜡预热温度80℃，反应温度80~100℃，氯气流量80~100m3/h，催化剂用量0.03%，添加剂A用量0.3%，反应时间5.5~6.5h，稳定剂用量0.15%。

For the heat input of 8kJ/cm and preheated temperature of 60℃, impact toughness value of specimen was highest for the formation of fine grains and a certain quantity of granular bainite which can effectively partite lath bainite.

当采用8kJ/cm的线能量和60℃的预热温度时，粗晶区的晶粒较细，组织由板条贝氏体和一定量的粒状贝氏体组成，由于粒状贝氏体对板条贝氏体的分割作用，使板条贝氏体的长度较小，方向性差，表现的韧性最优越。

As the steel carbon and alloy elements working together to make it extremely easy to lead in the welding hardened organization, welding poor performance should be this, pearlitic heat-resistant steel in general preheating before welding, after welding tempered.

由于钢中碳和合金元素的共同作用，使其在焊接时极易形成淬硬组织，焊接性能较差，应此，珠光体耐热钢一般焊前进行预热，焊后进行回火处理。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。