预烧

Through a systematic review about the development of late years on municipal sludge's disposal by mix-combustion with coal, the environmental allowableness, the thermal performance and the process feasibility of the technology was deeply discussed, the technical characteristics and the present problems was analyzed also. It is proved that, there is evidently technical rationality and good prospect about the technology, and there is also need to perfect and develop the technology in combination with municipal sludge's pre-treating and mix-combustion.

通过系统地分析国内外近期相关研究成果，深入地讨论了城市污泥与煤炭及其他燃料混烧处理技术的环境相容性、混烧热工特性和混烧工艺可行性，研究了城市污泥混烧处理工艺的技术特点和存在问题，认为污泥混烧处理技术具有明显的技术合理性和良好的发展前景，但在污泥预处理与混烧技术的结合方面还需要进一步完善和发展。

A new process for treatment of high-sulphur and high-arsenic gold concentrate was studied, with included the roasting at lower temperature with the addition of alkali fusion agent and the cyanidation leaching with the addition of active additive.

摘 要：研究富硫高砷金精矿在加入碱熔剂经低温焙烧预处理后，再加活性添加剂条件下的氰化工艺，结果表明，金的氰化浸出率从直接氰化或沸腾炉焙烧后的焙砂氰化的30%～50%提高到87%～93%，浸出速度也有很大提高。

The main research contents and results are shown as follows:(1) In order to meet the actural need of this research project, the general ways to bake electrolyzer, which include Aluminium-liquor- baking method, coke-ash-baking method and graphite-powder-baking method, are introduced in details. Their shortcomings and effects on the life-span of electrolyzer are also analyzed.

全文的主要工作和成果总结如下：(1)根据实际科研项目的需要，对现有的预焙电解槽焙烧启动方法铝液焙烧法、焦粉焙烧法和石墨焙烧法进行分析，指出其缺点。

The technological parameters of the productive process of light magnesium oxide by ammonium bicarbonate-ammonia pyrogenation technology had been studied.

研究了碳酸氢铵氨水热解法制备轻质氧化镁的工艺条件，考察了原料Mg2+浓度、反应温度、Mg2+与NH3t当量比、NH3与NH4HCO3摩尔比和预氨化pH值对碱式碳酸镁的过滤性能、沉镁效率和碳酸氢铵消耗量的影响，并探讨了煅烧温度、煅烧时间、升温速度对轻质氧化镁视比容的影响。

In this paper, two assemblies of special test equipments have been designed and fabricated by authors in our laboratory: namely Catalyst Molding Process Analyzer and Catalyst Mechanical Process Tester. These new skills are developed for the dynamic studies on whole mold forming process and crushing process of Fe-Cr WGHS catalyst pellet. Based on the orthogonal experimental design, the effects of some factors during the forming process of solid catalyst, such as predensification proportion, calcination time, calcination temperature and content of graphite on the mechanical strength of catalyst pellets are systematically examined, and the molding conditions have been optimized. Based on the experimental data, the relationship between catalyst density and forming pressure are educed, and the physical significances of some related parameters are described. The parameter of macro scopic elastic moduls has been suggested to character the mechanical properties of molding catalyst. The effects of molding pressure on mechanical properties of catalyst pellets are discussed, and results show that there exists a optimal molding pressure for the ideal mechanical properties: when over-high or over-low pressure is applied, the specific surface area and side crushing strength of catalyst pellets will decreased. The "rebound effect" will be undermined by the unsuitable pressure maintain process, resulting in the apparent decrease of mechanical strength of catalyst pellets.

本研究通过自行设计制造的催化剂模压成型过程分析仪（Catalyst Molding Process Analyzer， CMPA）和催化剂力学性质测试仪（Catalyst Mechanical Properties Tester， CMPT），以Fe-Cr系高温变换催化剂片剂为研究对象，对成型过程和受压破碎过程提供了全过程动态研究的新手段；本研究利用正交实验设计方法考察了固体催化剂成型过程中诸因素（包含预密致比例、煅烧时间、煅烧温度和石墨含量等）对催化剂成型体强度的影响，并对成型条件进行了优化；根据实验结果，关联确定了固体催化剂成型过程中的密度－压力关系式，并对方程中诸因子的物理意义进行了描述；提出了一种利用宏观弹性模量来表征成型催化剂的力学性质的方法；研究讨论了成型压力对催化剂成型体强度性质的影响，结果表明：对于催化剂成型体的强度和比表面性质，成型压力存在着一个最佳值，过高的成型压力会导致比表面积和侧压强度的降低；不适当的成型压力的维持时间会破坏&压力回弹&作用，造成催化剂成型体的机械强度明显降低。

Results The SiO2-ZrO2 composites were calcined at 200℃ prior to sulfating, the concentration of sulfuric acid was 1.0 mol/L ,the molar ratio of Si and Zr was 15, the calcination temperature was 500℃, the molar ratio of ethynol and lactic acid is 3/1, the yield of the ester could reach 92.7%.

结果SO4^2-／SiO2-ZrO2固体超强酸催化乳酸乙酯的合成反应适宜的反应条件为：预焙烧温度为200℃，浸泡硫酸浓度为1.0mol／L，硅锆摩尔比为15，焙烧温度为500℃，醇酸比为3时，酯化率可达92.79／6。

The effect of domestic GCC and clay on pre-coating coverage of the coated kraft liner board was studied. In order to optimize the second pre-coating, the effect of using TiO2 and using calcined clay to replace part of the TiO2 as the pigment on the coating coverage in the second pre-coating was also investigated.

研究了国产GCC、高岭土两种颜料及其不同组合对涂布牛皮卡纸预涂覆盖性的影响，并在此基础上，对二次预涂进行优化，研究了二次预涂中添加进口钛白粉及用国产煅烧高岭土部分代替进口钛白粉和高岭土对涂层覆盖性的影响。

After different sediments ignitions, S was 1.64~2.25 times of that of raw sediment, higher obviously than the sediments without ignition. The aerating pretreatments of sediment and water caused the transformation of bioavailable form to nonavailable form. The bioavailable phosphorus decreased 7.02% and 0.23% respectively compared with that before pretreatment, but the bioavailable phosphorus of the blank test sediment increased 4.85%.

不同底泥灼烧后，最大吸附量为天然底泥的1.64~2.25倍，且明显高于未灼烧底泥对底泥曝气与对水曝气预处理使易被生物利用态磷向难被生物利用态磷转化，易被生物利用态磷较预处理前分别减少了7.02%和0.23%，而空白试验底泥的易被生物利用态磷则增加了4.85%。

By analysis on baking data of 300kA large-type prebaked cells,the deficiency existing in original baking start-up process was discovered,and then improvement measures were taken accordingly.

本文通过300kA大型预焙槽焙烧数据的分析，发现了原来的焙烧启动过程中存在的不足，采取了改进措施并得了好的效果。

Fried "Wai Shan"- which again if you are vegie lover like me, I can finish the dish myself; if not, you might not like the Chinese medicine tatste of it.

我的烧鲭鱼预了要等，出来又几好吃，虽然皮烧得有些不平均，但鱼肉甘腴油润，伴著萝卜蓉，洒上柠檬汁吃，也很不错。

The reasons of iron ions content overproof in grade Ⅱ desalting water system,such as variation water quality,contamination of regenerant , operation adjustment of pretreatment system and switching operation of bed were discussed.

对二级脱盐水系统中铁离子含量超标的原因，如来水水质发生波动、再生剂受到污染、预处理系统操作调整、床体运行切换等进行了论述。

You were hired to drum up new business, so go and do it.

公司雇你招徕新业务，你就做你的事好了。