预先加热

The utility model relates to an appliance switch for controlling temperature The on or off at the predetermined temperature of the heating element switch is controlled by the deformation of the heated bimetallic strip, causing the heating element to heat.

实用新型与开关在发热设备开关被预先决定的温度由激昂的双金属带的变形控制的控制温度的一个装置开关关连，造成发热设备加热。

In its original state, a CD-WO player recognizes a track consisting of lands. The absorption layer in the pre-grooved trackis heated to above 250 with a laser three to four times the intensity of a reading player.

在初始状态下，CD-WO播放器读出的轨道上均为非凹坑，处于预先挖槽的轨道中的吸收层被超过250°C的高温加热，这个激光强度是一般读盘播放时强度的3∽4倍。

A stumper with required structures is pressed into the surface of polymeric foil and heated to a temperature above its glass transition temperature under suitable pressure until the temperature droped below the glass transition temperature of the polymer, followed by removal of the stumper and left the structures of the stamper in the polymeric foil.

将聚合物加热到其玻璃转化温度以上，利用预先制备好的模板在适当的压力下压向聚合物样品，保持压力直到聚合物温度降到玻璃转化温度以下，将模板移去后，模板上图形便转移到样品表面。

This research is a new low cost method of producing abrasive grit. It is to put the iron ore concentrate, coal powder, hydrated limed and addition agent together to make coal mixed pellet in prior which is rapidly auto-reduced in high temperature and kept about 10min above 1350℃, and then furnace cooled. The 2CaO·SiO2 of slag phase change、volume increase and natural bloom in reduction process. Finally we obtain no-slag abrasive grit through screen separation , in which the iron yield can be above 90%,the sulfur content can be below 0.05% and carbon content is lower than 4.0%.

本研究是一种全新的低成本生产铁粒的方法，它是将铁精粉、煤粉、消石灰和添加剂预先制成球团，在高温下迅速加热还原，在1350℃以上保温10分钟后随炉冷却，渣相中2CaO·SiO2在冷却过程中发生相变，体积膨胀而自然粉化，通过筛分便可以得到不含炉渣的铁颗粒，铁的收得率在90%以上、S≤0.05%、C在4.0%左右。

Dielectric heating is a convenient method of heating the preforms.

电阻加热是加热的方法中方便被预先形成。

Clinkers are nodules (diameters, 0.2-1.0 inch [5-25 mm]) of a sintered material that is produced when a raw mixture of predetermined composition is heated to high temperature.

水泥熟料是一种烧结的小颗粒(直径通常是0.2-1.0'')，由预先确定了化学成分的生料混合物加热至高温而得到的。

3 Mill in fine raw materials should be put in after the first injected fuel injected powder, and should be put at the turn of the harsh fat, cocoa liquor should be pre-cut into small pieces, heating dissolved (temperature not exceeding 50 ℃) may invest .

4.3精磨机在投放原料时应先投放油料后投放粉料，并应分次交替投放苛刻脂，可可液块应预先切成小块，加热溶解（温度不超过50℃）后方可投放。

The study on improving tough hardness of 65Nb steel which is used for new type cold working mould has been made.The result shows that 65Nb steel can achieve high tough hardness when it is spheroidized after full forging in fore heat treatment and is high-tempered for three times after high heat quenching in final heat treatment.

对新型冷作模具用钢65Nb 进行了提高强韧性的工艺研究，结果表明：65Nb 钢预先热处理采用经充分锻造后球化退火，最终热处理采用高温加热淬火后三次高温回火可获得高的强韧性。

Place the units to the heated laminator.

把预先叠放好的光电构件以玻璃面朝下放入加热的层压机里。

A hot runner with an externally heated material pipe and die tip comprises a pre-mounted heating unit with a sealing body which supports a pipe for a heat sensor in a circumferential segment.

一热流道带有外部加热的料管和接模喷嘴，包括有密封体的预先安装的加热单元。密封体在其周界的弧段上支承温度检测器的检测器管。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。