顺序

C The profile is of berm, which the section below the berm is concave. Using the polynomial curve to fit the shapes of the mean profile, the exponential equation of the equilibrium beach profile in South China was established, which has a general form: y=〓+ C. 2 It's obvious for the beach processes to vary with seasons. The main variation processes of beach profiles are composed of four kinds of mode which are the equilibrium profile mode, the berm mode, the foreshore mode and the bar mode. 3 Beach systems of the arc-shaped coast in South China exhibit an wide range of morphologic and dynamic variability with respect to both time and local environment.

此外，采用多项式曲线对平均剖面进行拟合，建立了华南海滩均衡剖面的指数公式y=〓C+。2）海滩具有较明显的季节性变化，海滩剖面的变化模式一般可分为均衡剖面模式、滩肩模式、前滨模式及其沙坝模式等4种。3）海滩不同岸段的动力地貌状态在同一空间上的分布具有一定的连续性，在时间上具有一定的更替顺序。

The second lens group includes a 2nd-group 1st positive lens, a 2nd-group 1st compound lens formed by joining a 2nd-group 2nd positive lens having a convex surface on the image plane side and a 2nd-group 1st negative lens having a concave surface on the screen side, and a 2nd-group 3rd positive lens arranged in that order from the screen side toward the image plane side.

第二透镜组包括一个第2组第一正透镜，一个由在像平面侧具有凸面的第2组第二正透镜和一个在屏幕侧具有凹面的第2组第一负透镜结合的第2组第一组合透镜，和一个第2组第三正透镜，它们以从屏幕侧到像平面侧的顺序布置。

The third lens group includes a 3rd-group 1st meniscus lens having a concave surface on the image plane, a 3rd-group 1st compound lens formed by joining a 3rd-group 1st negative lens having opposite concave surfaces and a 3rd-group 1st positive lens having opposite convex surfaces, and a 3rd-group 2nd meniscus lens having a convex surface on the image plane side arranged in that order from the screen side toward the image plane side.

第三透镜组包括一个在像平面侧具有凹表面的第3组第一凹凸透镜，一个由具有相对凹面的第3组第一负透镜和一个具有相对凸面的第3组第一正透镜结合的第3组第一组合透镜，和一个在像平面侧具有凸表面的第3组第二凹凸透镜，它们以从屏幕侧到像平面侧的顺序布置。

By using informational and personal resources , workflow management deals with all steps of a business process concertedly, by which the business process will be implemented step by step according to certain rules and be executed automatically.

工作流管理主要是通过调用有关的信息资源和人力资源来协调业务过程中的各个环节，使之按照一定的顺序依次进行，从而实现业务过程的自动化。

At the end of this paper, some concluding remarks on this research and future work are provided.

本文按时间顺序，分别介绍了两类模型中的突出工作和技术成果，并分析了它们的优缺点，最后对这一研究课题的进一步的发展趋势进行了讨论。

The skipping of various instructions as developed by a predetermined set of programming conditions. If a conditional jump is not used, the next instructions would follow in the normal proper sequence .

根据预定的一组程序设计条件，确定各种指令的跳转，如果不使用条件转移，则将以通常顺序进入下一指令。

The skipping of various instructions as developed by a predetermine d set of programming conditions. If a conditional jump is not used, the next instructions would follow in the normal proper sequence

根据预定的一组程序设计条件，确定各种指令的跳转，如果不使用条件转移，则将以通常顺序进入下一指令。

Oil some orders are to pay attention to driving the behavior to dawdle that the result of study reveals the limousine driver: Open the car light, driving a vehicle steadily of more than 100 kilometres per hour, driving a vehicle steadily of 50 to 70 kilometers of speeds per hour, it make air conditioning, engine last number of times, take number of people, speeds idle, wet, cloudy day, 70 to 90 kilometer is the urgent to drive a vehicle, pass through go up a slope by highway section,etc.

研究结果显示小客车驾驶者注意驾驶行为耗油部份顺序为：开车灯、时速一百公里以上的平稳行车、时速五十到七十公里的平稳行车、开冷气、引擎启动次数、乘载人数、怠速、行经地面潮湿路段、阴天、时速七十到九十公里的急加速行车、行经上坡路段等。

The interactions among the three active sites---N3, 04 and 05 in the most stable conformer of glycine and the three mono-value cations--~ Li~ and Na~ are investigated at the R0B3P86/6-3 1 G* level. Their relative binding strength and the binding order are compared and analyzed when the same active site reacts with three different cations or the same cation reacts with three different active sites, respectively.

利用限制性的DFT方法和6-31G基组函数，考察了甘氨酸的最稳定构象中的三个活性位：N3、O4和O5与单价阳离子H~+、Li~+和Na~+相互作用的情况，比较分析了三活性位与同一阳离子相互作用时的相对强弱和同一活性位与三个不同阳离子作用时的成键顺序。

Fibrations of congruence of lines and applications of sections ;2. The few group section is calculated for several in core assemblies,and the parameter section table is ordered by different Gd 2O 3 weight percent, burnup, energy group, and then the necessary sections for in core burnup are calculated with function .

本文介绍的组件均匀化参数计算的处理方法是以先进的燃料组件软件包TPFAP为基本工具，对于堆内各种类型组件计算少群截面，按Gd2O3不同重量百分比、比燃耗、能群等顺序组成参数截面表，再用函数插值法求得全堆燃耗计算所需的截面。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。