面

Before washing a face, want first will double hand is abluent, if the hand is dirty or when be stained with oil, the medicine that wash a face is not easy epispastic, wait for the agent that wash a face to send bubble hind adequately to be wiped gently again by in facial ministry, cannot have exerted oneself to do sth.

洗脸前，要先将双手洗净，如果手脏或沾有油时，洗面剂则不容易发泡，待洗面剂充分发泡后再轻轻地抹按在脸部，不能用力过猛，否则会伤害角质层。

The results are presented and compared with the available results of other authors, which shows satisfying agreement. And a submerged body beneath the free surface in accelerated motion is considered; the numerical results of instant wave resistance and free surface elevation are presented and discussed.

对非定常线性兴波问题的求解，第5章作为算法的验证，从较简单的近自由面运动潜体的非定常兴波问题入手，首先对无限水深近自由面潜体突然加速和渐近加速的非定常兴波问题作了计算，给出了非定常兴波波形和非定常兴波阻力随时间的变化曲线，计算结果与其它文献给出的结果进行了比较，其吻合程度令人满意。

In ACIS, function can be usedto form law, then the law would be used to produce curve.

在ACIS 造型工具中，可以利用函数来构造规则，然后利用规则来直接产生曲线，利用曲线按照一定的方式来产生面，然后将面按照一定的路径扫略来生成实体；本章就针对生成曲线的函数加以讨论，利用遗传算法的相关理论进行编码和进化操作，然后由用户对产生的子代进行评价，从而产生形式多样的子代实体。

This thesis discusses the following. First, we use the condition of inference and the concept of wildhabor cone to design the addendum circle. Second, we use TCA technique to obtain the relationship between the slip track and the angle of action, which then leads to the calculation of contact ratios. We can then design the tooth face width and the numbers of teeth based on contact ratios.

本文一开始先对空间渐开线齿轮之齿冠圆范围使用齿轮干涉条件与Phillips提出的Wildhabor Cone进行设定，再利用Litvin提出的齿面接触分析方法，得到空间渐开线齿轮对在啮合过程中作用角与滑动轨迹之间的关系，藉由此关系可以建立一套设计流程来调整齿面宽以及齿数等参数，使其能符合设计需求。

The addition amount of gardenia yellow, ash content of flour, food additive and process technology showed significant effects on the color of noodle.

研究了色素添加量、面粉灰分、面块添加剂和生产工艺等对面饼颜色的影响，以便为方便面企业的生产提供参考。

A laminated model of cutting face for evaluating cutting quality has been built up on the basis of cutting experiments. The experimental results and the theoretical analysis of the model show that, the lower part of the cutting face, adjacent to the bottom edge, has the worst cutting quality due to its worst roughness.

在工艺实验的基础上，建立了切割面分层理论模型，实验研究和模型分析表明：切割面近下缘处是切割质量的最薄弱环节，此处粗糙度最高，切割前沿在下缘处的温度是决定下缘质量的主要因素。

In the typical setup of Michelson interferometer, turning the tested object a small angle generates an air wedge between the object plane and the reference plane. The wedge produces equal thickness interference fringes.

采用典型的迈克尔逊干涉光路，将物体偏转一微小角度（等效为物面与参考面间形成空气楔）产生等厚干涉，可在物体的表面引入包含物体高度信息的载波干涉条纹。

If u want to eat cheap chinese food at air-con place ask around for the nearest food court.

如果想去有空调的地方吃面，（新加坡太热，没空调，吃面不要热死。

Firstly,we generated two depth buffers for occluder and receiver,discretizing the occluder to micro-patches;then,we calculated the depth value of shadow for each micro-patch and estimated the visibilities of them;finally,we computed penumbra extent for each micro-patch and projected soft shadow map on the scene to obtain real-time soft shadows.

首先为场景中遮挡物、接收面计算深度缓存，并离散遮挡物成许多微面；接着计算每个微面的阴影深度值，估计微面的可见度；最后计算微面半影范围，将软阴影图投影回场景中，得到实时软阴影。

The result shows that the crustal deformation is changing a lot in NW China: the deepest Moho is beneath the conjuction of west Kunlun and Karakorum, about 90 km deep, the shallowest Moho is beneath Jayir mountain to the west of Karamay, about 35.5 km; the Moho depth in the western segments of Tien shan is deeper then the mindle and eastern segments; there are Moho offset beneath Altyn fault, central Tien Shan northern margin fault and so on.

结果表明：比起我国其他地区，西北地区莫霍面无论是埋深还是形态均变化最大，反映出受印度板块与欧亚板块碰撞影响，西北地区地壳整体变形强烈。莫霍面最深（约90 km）位于西昆仑与喀喇昆仑构造结合处，最浅处位于准噶尔盆地西缘的克拉玛依（约35.5 km），最深与最浅差约55km。在盆山结合部位及大型走滑断裂，如阿尔金断裂、中天山北缘断裂带等均存在莫霍面错断。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新