面

The evolvement of grain orientation for the sheets during this processing and the influence of channel clearance on it were investigated.The results indicate that the shear stress and compression stress are put on the sheet at the channel corner during equal channel angular rolling.And the shearing deformation on...

结果表明，在等径角轧制过程中，板材在模具转角处受到剪应力和压应力的作用；随通道间隙的增加，板材的变形由剪切变形演变为剪切+弯曲变形，甚至弯曲变形；由于剪应力的作用，AZ31镁合金板材的晶粒取向由普通轧制所形成的基面取向转变为等径角轧制后的非基面取向，随着剪切变形量的减小，基面沿轧制方向的偏转角度也逐渐减小。

Non-extension and equal shortening plane: The plane that cut through the center of the strain ellipsoid is normally elliptical but there are two tangential, global and strain ellipsoid circular sections.

无伸缩面与等伸缩面：切过应变椭圆球体中心的面一般为椭圆形状，但其中有两个切面的球形的，较应变椭球的圆截面。

Diversity of soil surface, stone gully and stone pit is 1.199, 1.592 and 1.962; evenness index of soil surface, stone gully and stone pit is 0.616, 0.989 and 1.095; dominance of soil surface, stone gully and stone pit is 0.545, 0.353 and 0.245 in soil macrofauna community structure.

土面生境土壤动物的多样性指数为1.199，石沟的为1.592，石槽的为1.962；土面生境土壤动物的均匀性指数为0.616，石沟的为0.989，石槽的为1.095；土面生境土壤动物的优势度为0.545，石沟的为0.353，石槽为0.245。

G. cutting roots from 4 surface on the position 20cm away from the stem base nor cutting roots too near from stem base e.

若断根数量太多（如距茎20厘米处4面断根），或断根位置距茎基部太近（距茎基部10厘米处1面或4面断根），都不利于叶片含钾量提高

Shapes are: round, semi-circular, square, rectangular, horse eye, pear-shaped, side ladder, egg, heart-shaped, triangular, five-pointed star, plum,é, drilling in the drilling, Kite, fan-shaped, diamond-shaped bridge shape, octagonal column, precious stones have finished at the end of noodle can be divided into conventional face, a pointed end, double tortoise, flat-bottomed, such as Su-noodle.

形状有：圆形，半圆形，正方，长方，马眼，梨形，梯方，蛋形，心形，三角形，五角星，梅花，滴珠，钻中钻，风筝，扇形，菱形，桥形，八角柱等，宝石成品面底有可分为常规面，尖底，双龟，平底，素面等。

The paper discusses the position relationship between the litter circles of torus and the section circle of sphere figured out the intersection of torus and sphere when the central axis of torus and sphere center in XOZ coordinate plane through coordinate transformation.

利用坐标变换使圆环中心轴与球心同在XOZ平面内，讨论了在该平面内圆环截圆与球圆的位置不相交、相切和相交时圆环面和球面的相交情况，并给出了判别圆环面、球面相交情况的流程图以及圆环面和球面相交实例。

By putting some amount of cement into soil sample, structured soil with macro-pores is prepared.

试验表明，胶结较强的结构性土具有明显的初始屈服面，在初始屈服面内，土体表现为弹性，超过初始屈服面土体表现为弹塑性。

This paper presents the Machining Tool geometry of the former flank, the main flank, flank, the main cutting edge, Under the cutting edge tip cutting plane, the main section, the former Kok, horn, wedge angle edge angle, pointed knife, the blade angle, vice horn, Under the Frontier concept, the concept of cutting consumption, and the general circumstances of their choice method for processing slender shaft. cast iron materials, aluminum, stainless steel, rubber materials, plexiglass material, cloth bakelite materials, high temperature alloys, aluminum-magnesium alloy, hardened steel, the typical trapezoidal thread, the thread Triangle, Speaking at the trapezoidal screw thread pitch of the Tool geometry of the selection methods and cutting the amount of cutting fluids reasonable choice.

本文介绍了在机械加工中车刀几何角度中的前刀面、主后刀面、后刀面、主切削刃、副切削刃刀尖切削平面、主截面、前角、后角、楔角主偏角、刀尖角、刃倾角、副后角、副前角的概念、切削用量的概念、以及一般情况下的它们的选择方法，进行加工细长轴、铸铁材料、铝合金、不锈钢、橡胶材料、有机玻璃材料、夹布胶木材料、高温合金、铝镁合金、淬火钢、典型梯形螺纹、三角螺纹、特在螺距的梯形螺纹等的车刀几何角度的选取方法切削用量及切削液的合理选择。

To reconcile into a face block; rubbing more than about half an hour to become soft, flexible, tough both cooked noodles, and then do pure mung bean powder surface, with surface pressure into a thin stick rolling to quickly cut to the same small size, the final together by breaking into the specification to become finished products.

调和成面块；揉和约半小时以上，使之成为软、柔、韧兼备的熟面，再用纯绿豆粉做铺面，用面杖擀压成薄片，以快刀切为粗细一致的细条，最后按规格断拢成把，成为成品。

The only principle for cooking spaghetti is make sure it's "al dente", not over cooked, so while boiling the spaghetti, add in also salt it's necessary.

做好吃的义大利面把握的唯一原则就是：面务必要煮的弹牙，所以煮面时要记得加盐。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新