面

I usually use spaghetti because it's what I have, but I prefer to use fusili or rotelle because the pesto sticks to it better.

我通常用那种意大利长面（即大家所熟知的"意粉"，因为我家只有这种，但是我更倾向于用螺丝面或者车轮面，因为这两种面更容易使青酱附着在上面。

The tongs all passes in the machine the gearing on the bed what tongs the gearing on realizes with superficial contact in the cowgirl on the bed in machine or matches.when the tongs installs in the machine bed work on the stage,the center of gravity of the tongs should be as far as possible low,center of gravity the more high an accepts should the dint is more big,the tongs bottom four directions should bulge,make its contact good,or the bottom establishes four a feets.when the tongs installs on the machine bed principal axis,the tongs install the to should have the enough match accuracy with principal axis cowgirl surface,and guarantee the gearing the stability dependable.

夹具体在机床上的安装都是通过夹具体上的安装基面与机床上的相应表面的接触或配合实现的。当物流设备需要的公司体在机床工作台上安装时，夹具的服装厂应尽量低，重心越高则支承面应力越大，夹具底面四边应凸出，使其接触良好，或底部设置四个支脚。当夹具体在机床主轴上安装时，夹具安装基面与主轴相应表面应有足够的配合精度，并保证安装稳定可靠。

Concept of leakage coefficient of rod pump and amendment of its calculating method

性质：为修饰改善原料皮及加工中造成的粒面缺陷，通过磨革磨去革面较浅的伤残，经涂饰和压成假粒面，建立一个新的表面，经这样修饰的面革称为修正面革。

An improved method for measurement of complex permittivity using six-port reflectometer is presented. Error caused by incomplete superposition between the measured plane and reference plane, which is often in the case of conventional measuring method, is eliminated with the developed novel algorithm by separating the two planes.

提出了六端口反射计测量介质材料复介电常数的一种改进方法，新的算法使测量面与参考面分离，消除了传统测量方法中测量面与参考面无法完全重合引入的误差。

For the slope protection,domestic and foreign have various methods,such as:clean surface, and shotcrete stone surface and the use of concrete,asphalt,riprap,etc.,but these have a fatal weakness,the use of clean face,and shotcrete stone surface and the use of concrete,asphalt,riprap protection methods such as the slope,often due to excessive destruction of the human impact of the original natural and ecological environment.so that the entire road is almost formed a gray line,and While these protective measures outside the slope formed a protective layer of solid layer,but if there is a protective layer of water into the lower water flow and form,these protective measures will also be destroyed.

对于边坡的防护，国内、国外均有多种方法，比如：抹面、喷浆、石砌护面以及利用混凝土、沥青、抛石等等，但这些都有着致命的弱点，利用抹面、喷浆、石砌护面以及利用混凝土、沥青、抛石等方法进行防护的边坡，往往由于过多的人为影响破坏了原来的自然生态环境，使整条公路几乎形成一条灰色的路线，同时，这些防护措施虽然在边坡外面形成了一层坚固的防护层，但只要有水渗入防护层下部并形成水流时，这些防护措施也将被冲毁。

The purposes of this study were (1) to compare the differences of the transverse craniofacial morphology between the adult high-angle and low-angle facial skeletal types, and (2) to correlate the width measurements with data obtained from PA roentgenogram. Thirty-seven adults, 18 to 22 years old, with varied vertical facial types were separated into two groups: seventeen high-angle, twenty low-angle facial skeletal types.

高低角骨面型是垂直向发育异常所造成的两种极端骨面型，近年来逐渐成为学者们研究的热点，目前的研究大多是基于头颅侧位X线片从矢状向和垂直向进行比较，而未查及高低角骨面型横向颅面结构的系统性研究。

B For the relationship between dimensions of consciousness of industry cultural activities and dimensions of package design of agricultural/special products, my results indicate that cultural rootage, sightseeing leisure, and industry improvement have significant influence on seeing effect, market consideration, and package structure dimensions.

b在产业文化活动意识构面与农特产品包装设计构面之关联性方面，整体而言，产业文化活动意识主要是经由「文化扎根」、「观光休闲」及「产业振兴」三个构面，影响到农特产品包装设计之「视觉效果」、「市场考量」及「包装结构」等构面。

Its principle is based on that there are some rdationships between curvatures of the theoretical profile surface and the real profile surface Curvatures of theoretical profile surface,which is a ruled surface,are easy to get.

该方法利用等距曲面间的曲率关系进行凸轮廓面曲率的解析计算。由于理论廓面是直纹面，其廓面曲率容易求得。

Analyze the failure models of rock slope, and then classify the sliding plane, the sliding plane can be divided into self-born sliding plane, appendiculate sliding plane and mixed sliding plane, furtherly summarize the selection method of mechanics parameters to each types. Based on the classification, the author establishes the mechanics model of each sliding plane.

论文主要研究内容和结论如下：(1)阐明了边坡滑动面力学参数取值的研究对象、重点及其研究意义，简要回顾了滑动面分类、结构面强度取值、滑动面试验强度取值和力学参数反算的研究现状，针对目前研究中存在的一些问题，提出了本文的主要研究内容。

The shear yield surface in π plane and θ〓 direction are gained from the true triaxial test data.

用普通三轴试验数据拟合了体积屈服面与子午平面上q方向的剪切屈服面，用真三轴试验数据拟合了偏平面上q方向剪切屈服面与θ〓方向的剪切屈服面。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。