静电

Humidification of the workshop is to shop humidity environment to a more appropriate range, so that static electricity generated by the basis of the loss is to prevent static electricity from the fundamental (but note that: For a number of insulators to isolate the generation of static electricity, a single means of humidification not a good solution of the static problem, the need for the joint effect of a variety of ways).

对车间加湿是将车间环境湿度提高到一个较为合适的范围，使静电失去产生的基础，是从根本上防止静电（但需要注意的是：对于一些孤立的绝缘体所产生的静电，单一的加湿手段并不能很好的解决其静电问题的，需要多种方式共同作用）。

The control principle of electrostatic shaping was introduced according to the balance between electrostatic force and resulting force formed by membrane deformation and the complex shaping process of SMEC. Then, taking the trisection circularity electrode for an example, the distribution characteristic of electric potential in the electrostatic field was analyzed, namely, the expression of potential function in the electrostatic field was deduced by Laplacian equation. And then, by combining the difference equation with electric potential expression, the numerical solutions of electrostatic force in single electrode mode and trisection circularity electrode mode were disposed. Finally, the calculated figure was compared with the ideal paraboloid and comparison shows that more accuracy would be achieved by multi-electrode control.

根据静电力与薄膜变形载荷作用力之间的平衡关系和静电拉伸薄膜反射镜成形的复杂过程，介绍了薄膜反射镜静电成形的控制原理；以三等分环状电极为例，分析了静电场中空间电势分布特性，即从拉普拉斯方程推导出静态场势函数的表达式；然后，利用差分与电势方程结合的方法，对单电极电场力和三等分环状电极电场力进行了数值求解；最后，将计算面形与理想抛物面进行了比较，结果显示，单电极情况下得到的薄膜反射镜面形不是理想抛物面，若采用多电极控制可获得更高的控制精度。

The control principle of electrostatic shaping was introduced according to the balance between electrostatic force and resulting force formed by membrane deformation and the complex shaping process of SMEC. Then, taking the trisection circularity electrode for an example, the distribution characteristic of electric potential in the electrostatic field was analyzed, namely, the expression of potential function in the electrostatic field was deduced by Laplacian equation. And then, by combining the difference equation with electric potential expression, the numerical solutions of electrostatic force in single electrode mode and trisection circularity electrode mode were disposed.

根据静电力与薄膜变形载荷作用力之间的平衡关系和静电拉伸薄膜反射镜成形的复杂过程，介绍了薄膜反射镜静电成形的控制原理；以三等分环状电极为例，分析了静电场中空间电势分布特性，即从拉普拉斯方程推导出静态场势函数的表达式；然后，利用差分与电势方程结合的方法，对单电极电场力和三等分环状电极电场力进行了数值求解；最后，将计算面形与理想抛物面进行了比较，结果显示，单电极情况下得到的薄膜反射镜面形不是理想抛物面，若采用多电极控制可获得更高的控制精度。

The basic material is soft plastic which is divided three kinds:Anti-static PVC grid portiere,Anti-static PVC transparent portiere,Anti-static PVC black grid portiere.

防静电门帘采用软质PVC 为基材制作而成。分为防静电PVC网格门帘、防静电PVC透明门帘、防静电PVC黑色网格门帘。

The basic material is soft plastic which is divided three kinds: ESD PVC gridding portiere, ESD clarity PVC portiere and ESD black PVC gridding portiere.

防静电门帘采用软质塑料为基材制作而成。分为防静电PVC网格门帘、防静电PVC透明门帘、防静电PVC黑色网格门帘。

Is a professional agent distribution IWATA IWATA JAPAN automatic and manual air spray gun air spray gun; DEVILBISS medium voltage automatic air spray gun and the manual air spray gun, spray gun MEIJI Meiji Japan, paint÷·§; Taiwan Polaroid,, defended by a tiger, paint barrels stress; Sampoong, fifth, David Pneumatic double diaphragm pump; GRACO Pneumatic double diaphragm pump, stirrer; Switzerland GEMA electrostatic powder spray gun; JAPAN ASAHI liquid manual / automatic electrostatic spray gun / pump, pneumatic double diaphragm pump, paint regulator valve and electrostatic spinning cup spray gun and a variety of spare parts; JAPAN SSD, Taiwan crown Goods electrostatic dust guns, electrostatic Tester; GRACO high-pressure airless spraying machine; Taiwan Yuan-qi DISC electrostatic spinning disc spraying machines; high temperature chain oil, solvent paint tube, air-water separator, Taiwan Shi large adsorption / freezer dryer, pneumatic tools, spraying, cleaning, cooling, lubrication nozzle.

苏州恒大涂装设备有限公司是专业代理经销日本岩田IWATA自动空气喷枪及手动空气喷枪； DEVILBISS中压自动空气喷枪及手动空气喷枪、日本明治MEIJI喷枪、涂料调压阀；台湾宝丽、齐成、悍虎、涂料压力桶；三丰、五分、国宝气动双隔膜泵浦；GRACO气动双隔膜泵浦、搅拌器；瑞士GEMA粉体静电喷枪；日本ASAHI液体手动/自动静电喷枪/泵浦、气动双隔膜泵浦、涂料稳压阀及静电旋杯喷枪和各种零配件；日本SSD、台湾冠品静电除尘枪、静电测试仪；GRACO高压无气喷涂机；台湾元麒ΩDISC静电旋碟喷涂机；耐高温链条油、耐溶剂涂料管、空气油水分离器、台湾石大吸附式/冷冻式干燥机、气动工具、喷涂、清洗、冷却、润滑用喷嘴。

Grounding with a wire connected to ERTH is specially important, if not the printer might be damaged by spikes of static electricity, also the please pay attention that the material to write on is not charged with static electricity, also conveyors can easily be charged with thousands of volts of static electricity, this will damage the controller, so please remove all static electricity by sufficient grounding and correct termination of all potentials.

用电线与地面连接极其重要。如果喷印机没有接地，静电的调试脉冲就会损坏喷印机。另外，还应注意填写的资料与静电不一致，数千伏特的静电给传送机充电，导致控制器受损。因此，请通过充分的接地，改正所有电压的中止，去除所有的静电。

PVC Card - Business card printing 】 Electrostatic besetting business card printing and membership card to make a factor, this kind of static electricity is paper or filmogen in business card printing and membership card making, and roller friction or air ionization in paper or film produced by electrostatic, cards and membership cards to make quality a little, and the electrostatic is dedicated appliances, in cards and membership cards and business card printing and membership card in the process of making assisted processing.

静电是困扰制卡和会员卡制作的一个成分，此栽静电是纸张或薄膜质料在制卡和会员卡制作历程洋，与功辊磨擦或氛围电离在纸张或薄膜暗地爆发的静电，差制卡和会员卡制作质量有一点感化，而本文所涉及的静电是由附带的摆设爆发的，在制卡和会员卡制作及制卡和会员卡制作后工序洋起补助增工功用。

Discover antistat dosages, the ambient temperature and humidity city weighing to ultimate volume of foam material electric resistance.

发现抗静电剂用量、环境温度和湿度都会对泡沫材料最终体积电阻产生影响，用ASA2作为抗静电剂采用涂敷法制备了抗静电聚乙烯泡沫，当抗静电液浓度大于8％时，泡沫体积电阻降低到10~6O·m。

This paper presents conductive polymer molecular materials with insulating powder, mixed into the deployment of surge suppressors for low capacitance of paste, while the component design concept is based on the field of passive components, manufacturing process to make the basic theory to design the protective components, the main use of the existing ceramic substrate for the component body structure design, screen design in the body through the structure of the gap at the top of the printing layer of a different conductors, and then to learning to know the printing process technologies approach the low capacitance of the surge suppressor paste cover the gap in the two conductors, and by the resistance of plastic burning process technology, the temperature of sintering parts made of electrostatic protection element, and this protection through the external ESD components in bombardment tests, measurement of capacitance electrostatic discharge after bombardment, Trigger voltage and leakage current data, and the volume measured by the results of future discussion of the layout of this different style of work in the same area, different clearance, solid content and temperature than the next, for the attainment of performance components, a low capacitance ESD protection devices with low breakdown voltage requirements and to chip-based protection devices can be designed to integrate with the advanced Integrated Circuits or used independent of the electrostatic protection element in the system.

本文提出高分子导电分子材料搭配绝缘粉末，调配混合成适用於低电容突波抑制器之PASTE，而元件设计概念是以被动元件制程领域作基础理论去设计此防护元件，主体利用现有陶瓷基板为元件本体结构设计，在经由网版设计在本体结构上方印刷一层不同的间隙导体，再以习知印刷制程技术方式，将低电容突波抑制器之PASTE覆盖在两导体的间隙内，并经由电阻制程习知塑烧技术，将元件烧结适当温度制成静电防护元件；而此防护元件在经外加静电放电轰击测试后，量测静电放电轰击后的电容、Trigger voltage及漏电流相关数据，并藉由测结果讨此同的布局样式，在相同工作区面积、不同间隙、固含量与温度比下，对於元件效能是否达到静电防护元件低电容与低崩溃电压的需求，并藉此晶片型防护元件可设计整合於先进积体电或应用於独系统的静电防护元件中。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。