零位置

The electronic digtal calipers apply LCD digital disply and can make metric-inch interconversion and reset at any position.

电子数显卡尺采用LCD数字显示并可进行公英制转换，在任意位置置零；还具有输出功能。

In order to improve our CNC system to a higher level, an interpolation problem of circular in an arbitrary plane was also studied in the paper, where three kinds of interpolation algorithm were given, their feasibility were analysed and compared, and the best algorithm was obtained; In the end of this paper, a new concept of zero—following error position control was advanced, whose control principle and algorithm wre derived.

为使数控系统向更高档次发展，本文还研究了空间圆弧插补问题，给出了三种插补算法，通过分析比较，得到了最佳算法，并用汇编语言进行了可行性验证；在本文的最后，提出了零跟随误差位置控制的概念，并推导出了控制原理和算法。

For each data bit sent or received,the high order bit of the current remainder is XORed with the data bit and then the remainder is shifted left one bit and the low-order bit set to zero.

对于每个被发送或者被收到的数据位，当前余项的最高一位和数据位进行异或，然后，余项是左移1位，并且，最低一位置零。

How to measure the program zero point location on the machine Figures 11-3 and 11-4 show a setup for a vertical machining center and stress how the program zero piont measurements can be made.

如何到尺寸那计画零点位置在机器上图 11-3 和 11-4 表演一种装备为一垂直的机制中心和压迫力如何那计画零 piont 测量罐子是制造。

To solve the second problem, an approach of irregular QC LDFC codes is proposed. The proposed approach is to replace some sub-matrices by zero matrices and identity matrices at special positions in the given sparse parity-check matrix so as to get a nonsingular square matrix for the construction of the generator matrix.

为解决第二个问题，提出一种不规则准循环LDPC码的设计方法，该方法将校验矩阵中的特定位置的子矩阵用零矩阵和循环矩阵置换，获得一非奇异方阵，用于构造生成矩阵。

We can refer each control using the zero-based ordinal position of the column.

我们可以参考每个控件使用从零开始的列序号位置。

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

Their mathematical achievements included positional notation and the use of zero; in astronomy, they accurately calculated a solar year, compiled precise tables of positions for the Moon and Venus, and were able to predict solar eclipses.

他们的数学成就包括位置符号和使用的零，在天文学，他们准确地计算出太阳年，编制为月球和金星阵地的确切表，并能预测日食。

In this thesis, we investigate and show how to achieve both practical and general zero-knowledge systems that can be securely run in concurrent and resettable settings with both concurrent prover security and concurrent verifier security in general public-key models.

因为零知识证明系统在当代密码学中处于中心的位置，并且由于Internet以及Internet上基于智能卡的电子商务的广泛普及和大规模应用，我们的工作具有极其重要的理论和实际意义。

In computing, to replace all the binary digits in a storage device by binary zeros, to replace all hole patterns on a punched paper tape by holes in every position.

在计算技术中，(1)用二进制零替换存储设备中所有的二进制数；(2)在穿孔纸带上的每个位置上都穿孔，以代替所有的穿孔模式。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。