零件

We can't find it in your enchiridion. Please inform us. Thanks.

的零件，我们在你们的黄手册上查不到，请告之，谢谢。

Piston ring is the important accessory of the engine and turning its contour is the key procedure to ensure the performance of piston ring.

活塞环是发动机中最关键的零件之一，其外圆轮廓仿型加工是保证活塞环性能的关键工序。

A TV set iS made up of hundreds of differ- ent parts .

电视机是由数百个不同的零件组成的。

In the processing of NC milling ,there are many kinds of methods to control the forging envelop of part.

在数控铣削加工过程中，对零件加工余量的控制方法有很多种。

The limit state equation of the component is constructed by the use of the new cumulative fatigue damage model.

利用本文提出的疲劳累积损伤模型，建立零件的极限状态方程。

Wear is one of three main industrial problems, that causes the component and equipment failure.

磨损是工业上导致零件和装备失效的三个主要问题中的一个。

In addition ,the thesis deals with amount of components devices and calculations ,including :(1) Choice of the main shaft and disposal of transmission , by doing so to ensure the accuracy of components machining in process when the main shaft rotating;(2)The device and check of the transmission shaft ,so it can assure the rigidity of the shaft is allowable ;(3) Gear device and calculations ,check the performance in the strength and rigidity of it ;headstock is a very important part in this thesis ,the design of it here not only ensures the rationality 、equipoise and stability of the motion of the slipway ,but also satisfies the requirements of different work environment .

液压装置的设计液压滑台、定位夹紧装置均为液压控制。并采用了许多液压控制阀，保证了运动的平衡性，循环性和精确性。另外，本文还涉及到大量的设计和计算，包括：（1）、主轴的选择和传动布置，以保证加工过程中被加工零件的精度；（2）、传动轴的设计和校核，以保证轴的刚度；（3）、齿轮的设计、计算，对齿轮的强度和刚度进行校核；多轴箱部分是本次设计的重要环节，本次设计中它的设计既要保证工作台的运动的合理、平衡和准确，又要满足工作要求。

It makes various dirty substances peel off from the cleaned surface,thus reaches the goal of erasion,By utilizing ultrasonic wave for rinse,it has advantages of quick cheaning speed,good effect,nodamage to spares and the decrease of labour intensity, costsaving etc.

利用超声波清洗具有清洗速度快、效果好、不损伤零件、减轻劳动强度、节约成本等优点。

By ERNESTI, 3 vols., Leipzig, 1773-4, and a continuation for the Middle Ages (1734-6, 5 vols.); the whole was re-edited by MANSI (6 vols., Padua, 1754, and Florence, 1858-9); LE NOURRY, Apparatus ad Biblioth.

1697 ， 1708 ， 1712 ，等编，由埃内斯蒂， 3卷，莱比锡， 1773-4 ），并继续为中世纪（ 1734-6 ，第5卷）；整个重新编辑曼西（ 6卷，帕多瓦， 1754年，佛罗伦斯， 1858-9 ）；乐nourry ，仪器及零件业专案

On the basis of measured data processing,error analysis,curve modeling and object modeling,it establishes the mathematical modeling of the screw parts of single screw compressors.

在测量数据处理、误差分析和曲线曲面造型、实体造型技术的基础上，建立了单螺杆空气压缩机螺杆零件的数学模型。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。