零件
- 与 零件 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
Approaching the Brazil coast near Recife the current diverges, the N part continuing WNW towards the Caribbean Sea (see 2.15) and the S part turning S as the warm Brazil Current.
Approaching在Recife附近的巴西海岸潮流分流, N零件继续往加勒比海的WNW (参见2.15)和转动S的S零件作为温暖的巴西潮流。
-
Casting for auto parts(calliper,bracket,disc,pressure plate etc),reerigerator and air conditioner compressor parts,machinicalparts,construction parts,motorparts, pump parts etc.
汽车用铸件(制动钳体、支架、制动盘、压盘等),机械零件,冰箱、空调压缩机铸件,建筑工程用铸件,电机零件,水泵等。
-
As the procurement planning specialist, be responsible for making parts requirement and expediting the ordering process to satisfy production capacity, and controlling parts inventory.
作为物料需求计划专员,负责制定零件需求计划,跟进零件订购过程,确保按时抵达以满足生产需求,并合理控制库存。
-
The compilatory method is used to study the grammar check, and the logic ruler method is presented; On the interference verification, the rapid algorithm of over—cut verification is presented, which can pre—verify multiple NC blocks.
采用编译理论对语法检查进行了研究,给出了零件程序的词法检查状态图,并提出了新的采用逻辑尺的语法检查方法;干涉校验方面,提出了一种新的过切削的快速校验算法,可以实时预校验多个零件程序段,提高了校验能力。
-
Certain features of the harvester are illustrated in somewhat schematic form in the interest of clarity and conciseness.
在下面的叙述中,所涉及到的所有相同零件均用同样的基准数来标注,某些零件将用少量简图的形式简洁明了地表示。
-
A new curvature-based algorithm in free-form curve fitting was proposed to fit a 2D NURBS profile with an arc spline ,where a new form of curvature formula with matrix representation was also proposed,and then the arc spline tool path with G~(1) continuity was generated.
给出了一种平面曲线轮廓的圆弧样条拟合及刀具路径生成算法,该算法面向零件轮廓的光顺性刀具路径生成,通过应用曲线的曲率关系,对以NURBS表示的被拟合自由曲线按参数递增的方向用G1连续的圆弧或直线段逐段拟合,并生成相应的圆弧样条刀具路径,从而实现零件曲线轮廓表面的光顺加工。
-
In general, the deformation pattern of ellipse shaped shell in dieless spinning is similar to that of a rotary one. Therefore, it is possible to spin a deep elliptic cylindrical shell if a cylindroid mandrel is adopted.
从总体上看,椭圆形锥壳零件的无芯模旋压和回转形锥壳无芯模旋压的变形规律相类似,由此可以推测,利用椭圆柱形芯模实现椭圆形深筒零件的旋压也是可能的。
-
Metal heating, the workpiece exposed to the air, it often happens oxidation, decarbonization (ie, reduce the carbon content of the surface of steel parts), This is part of the surface properties after heat treatment has a negative impact.
金属加热时,工件暴露在空气中,常常发生氧化、脱碳(即钢铁零件表面碳含量降低),这对于热处理后零件的表面性能有很不利的影响。
-
The spring steel 60 Si2Mn will be decarburized in heating process,and decarburization will reduce the performance of the machine parts.
弹簧钢制作的零件,在热处理过程中会严重脱碳,从而使零件的使用性能,特别是疲劳性能大幅度下降[1]。
-
However, in the case of deep-drawn contoured parts, wrinkling in the product area can occur from insufficient sheet material stretching.
不管怎样,在对整周零件拉伸时,不充分的薄板材料拉伸可导致零件褶皱。
- 推荐网络例句
-
Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.
Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。
-
I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.
我来只是现在,'歼灭战perfuming自己与胡努特,那麼,他来到和SAT 。
-
The shamrock is the symbol of Ireland and of St.
三叶草是爱尔兰和圣特里克节的标志同时它的寓意是带来幸运。3片心形叶子围绕着一根断茎,深绿色。