除雾

In this thesis, the influencing factors of mist eliminator are analysised by the experiment and numerical simulation.

本文采用除雾器除雾性能试验和数值模拟的方法，对影响除雾器除雾性能进行研究。

An the orthogonal test of mist eliminator is conducted, and it is found that the angle of corrugated baffle and Reynold number of gas have a great influence on both the separation efficiency and the pressure drop of mist eliminator.

首先对除雾器除雾性能进行正交试验，并采用直观分析法和方差分析法对正交试验结果进行了分析，发现波形板曲折角α对除雾效率η影响显著，对压降影响特别显著，α为45°时，除雾器除雾效率高且压降适中；斜边长与板间距比值L/b对除雾效率η有一定影响，但对气流压降影响不大；气流雷诺数Re对除雾效率η和气流压降影响显著。

On the basis of above studies, the performance of corrugated baffle demister with the angle that is equal to 45° is conducted, and the resistance coefficient and the classification efficiency of demisters are obtained.

在上面研究的基础上，对曲折角α为45°的波形板除雾器进行了试验，得到了除雾器的阻力系数和除雾分级效率。

Numerical simulations of demister vane with various geometries and operating conditions were performed to study the efficiency of droplets separation.

利用计算流体力学商业软件Fluent6.1对不同结构尺寸以及运行条件下波板型除雾器除雾叶片的内部流场进行了数值模拟，基于响应曲面法，利用统计软件MinitabV14得到了除雾效率的预测模型。

The computational fluid dynamics method is used to simulate numerically the two phase flow of gas and liquid in a demister with corrugated baffle. The demisting efficiency and pressure drop under various droplet diameters, gas velocities and plate spacings are provided. The effects of main design parameters on the demisting efficiency and pressure drop are analyzed.

用计算流体力学方法对波纹板除雾器内的气液两相流动进行了数值模拟，计算得到了不同液滴直径、进气速度与叶片间距下除雾器的除雾效率和压降，并分析总结了各参数对除雾效率和压降的影响规律。

Having in view the lozenge arrangement of demisters and diversely shaped plates , the pressure drop and flow velocity in demisters were measured during many tests , while the demisting efficiency and the concentration of liquid droplets were calculated by the liquid balance method the effect of flow velocity and that of plate pitch on demisting efficiency as well as the influence of the number of demister stages on both the efficiency and pressure drop have been analyzed , herewith providing some referential .

针对除雾器的菱形布置方式和叶片的不同几何形状，通过大量实验测定了除雾器的压力降和速度，利用水平衡法计算了除雾效率和液滴浓度，分析了除雾器气流速度，叶片间距对除雾效率的影响及除雾器级数对除雾效率和压力降的影响，为该型除雾器的设计和制造提供了参考依据。

DEMISTER~ style 713 knitted mesh mist eliminator provides increased efficiency with low pressure drop in drying towers,FLEXIFIBER~ BD-LdP Brownian Diffusion candle mist eliminator provides reduced pres- sure drop with no loss in efficiency in absorption towers and FLEXIFIBER~ ICK-LF impaction candle mist elimi- nator provides increased service life with no loss in efficiency in drying and fin...

DEMISTER~型713丝网除雾器，在干燥塔中使用可提高效率且具有较低的压力降；FLEXIFIBER~BD-LdP布朗扩散型烛式除雾器，在吸收塔中使用可减小压力降且无效率损失；FLEXIFIBER~ICK-LF碰撞型烛式除雾器，在干燥塔和二吸塔中使用可延长使用寿命且无效率损失。

Compared with some experimental and simulative conclusions , the results indicate that present prediction model can estimate the effects of different geometries and operation conditions on the separation efficiency , and can direct the optimum design of demisters .

与前人的实验和模拟研究相比，该文的预测模型可以更加直观的反映除雾叶片的结构尺寸和运行条件对除雾效率的影响，有助于除雾器的优化设计。

In order to improve demisting efficiency of mist eliminator in terms of different droplet diameter and reduce blockage of gas gas heater in desulfurization system, numerical simulation and experimental study were carried out on the mist eliminator in bubble desulfurizer.

为提高除雾器对不同粒径小液滴的脱除效果，减轻脱硫系统气气换热器的堵塞程度，对鼓泡脱硫塔除雾器性能进行了数值分析和实验研究。

The results of numerical simulation suggest that the demisting efficiency increases as droplet diameter and gas velocity increasing and decreases as the mist eliminator plate spacing reducing, and the efficiency of arc-shaped plate with barb mist eliminator is higher than that of polyline-shaped plate mist eliminator. Droplet with a diameter under 20 mm is of low demisting efficiency.

数值分析表明：除雾效率随液滴直径的增大而增大，随进气速度的增大而增大，随除雾器叶片间距的增大而降低；带倒钩的弧形板除雾器比折形板除雾器的除雾效率高；粒径小于20 mm的小液滴脱除效率较低。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷