降低速度

The experimental results prove that the convergence speed of the proposed method is non-linear and the use of convergence points can lower the complicacy of process of iteration.

实验结果表明，改进后的高斯核均值漂移算法以超线性的速度收敛，收敛点的应用降低了收敛过程中的计算量。

The pulse velocity of drilling fluid declined with increase of density and compressibility of drilling fluid.

随着钻井液密度和压缩性的提高，脉冲信号的传输速度降低。

The drop of bed temperature close to steam condensation point, the reduce of absorbent grain size and the charging rate, and the increase of absorbent surface area and the residence time were helpful for absorption.

降低床层温度，接近蒸汽冷凝点温度；减小粒径，增大吸附剂单位比表面积；减小进料速度，增大停留时间都将有利于吸附操作。

Some parameters such as Indoor radiation heat transfer, convective heat transfer, MRT, OT, radiation heat transfer coefficient, convective heat transfer coefficient, and PMV-PPD were calculated under a steady condition. From the result, we can conclude, when operation under the combination system and worst-case test, if floor temperature is about 21℃, supply air temperature is 21℃, air velocity is 1m/s, the equlvalent coefficient of heat transfer between floor temperature and OT is 13.6w/m2k, where 5.68w/m2k is equlvalent coefficient of radiant heat transfer, 9.48w/m2k is convective heat transfer coefficient. And when air velocity is higher, supply air temperature is lower, the radiant heat transfer between floor and others is lower. In the whole experiment, the floor temperature was keeping above the indoor air dew point, and condensation was not appeared.

通过分析计算，在复合式系统运行中，最不利室外环境下，当地面温度维持在21℃左右，送风温度21℃，送风风速1m/s，此时地板对作用温度的当量综合换热系数为13.6w/m2k，其中当量辐射换热系数为5.68w/m2k，对流换热系数为9.48w/m2k，并且送风速度越高、送风温度越低，地板与其他壁面的辐射换热量有一定程度的降低，但总供冷量增加；在整个实验中地板温度始终高于地板上层空气的露点温度，并未发现有结露现象；室内空气温度梯度能满足0.1m-1.1m的温差小于3℃的要求，并且适当提高送风温度可以进一步提高人体的热舒适性。

Short-run impatience of consumers results in the increment of tax rate, and consequentially the decline of capital accumulation rate.

消费者这种短期的非耐心导致了收入税率的增加，从而降低了资本的积累速度。

You would have to lower your rate considerably for this to make sense.

你将不得不降低你的速度相当大，这是有道理的。

The requirements of plastic parts required for automotive pro duction,the rapid model developing of motor vehicle and the requirements of cont inuous cost reduction of automotive products force to develop and adopt continuo usly the new production processes by automotive plastic part manufacturers.

汽车生产对塑料件的要求以及汽车车型开发速度加快和不断降低成本的要求，迫使汽车塑料件的生产厂家不断开发和采用新的生产工艺。

The change of contractile response and 〓 of small intestinal smooth muscle cell induced by Ach were quantified.

结果：手术组小肠的传输速度明显降低，小肠环行肌条的收缩能力明显下降。

In the new algorithm, SCA provides global convergence by moving the equalizer weight vector in the correct direction. After the equalizer enters the local convergence region, SDD can decrease the residual inter-symbol interference and accelerate convergence speed by maximizing the posteriori probability of the equalizer output.

该算法一方面使用了SCA算法来提供全局收敛，保证在整个收敛过程中，均衡器朝正确的方向收敛；另一方面当均衡器进入到局部收敛区域时，并行增加的SDD部分通过最大化均衡器输出的局部后验概率来降低剩余码间干扰和提高收敛速度。

The new method does not require the formation of the covariance matrix and its eigendecomposition.

不仅使得智能天线的结构尺寸减小了30%，通过多级嵌套维纳滤波器前向递推的方法，子空间的分解和维数确定可同时进行，不需要估计接收信号的协方差矩阵和对其作特征值分解，运算量可以明显降低，收敛速度快。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。