阀片

On the other hand, the theory and methods can strongly supportparameters optimization of shock absorber detail design work.

在这些问题中，减振器阀片挠曲变形量的计算对仿真结果的影响很大。

The technological characteristics of the valve of the shock absorber were analyzed.

分析了减震器中阀片的工艺特点，介绍了其模具结构的确定原则和模具的加工方法。

According to the failure style of the air valve of industrial compressor,the fracture and static stress are analyzed.

针对工艺用压缩机气阀的失效形式，对损坏的阀片进行了断口及静态应力分析。

The physical model of a throttle valve with an annular throttle slice is built.

建立了带有环形节流阀片的阻尼阀物理模型。

Single or double-acting,three position double-actingdouble direction location,auto resetetc,on which relief valva and pressurelimiting valves may be added,on each port to restrictpressure in the port and avoid the damage caused by higher impact pressure to the system..

该阀的每一工作阀片可分为三位单、双作用；三位双作用双向定位、自动复位等不同功能，可加装安全阀，并可在每一个工作油口加装过载阀，限制该油口压力及防止冲击压力过高对系统引起的损坏。

Reasonable movement of discharge valve has great influence on flowing losses and life of valve.

排气阀片的运动规律合理与否，关涉到排气孔口处的流动损失及阀片的寿命。

The valve motion, the work process of the cylinder and the change of the pressure in the valve chamber are related by "pressure inspire", and the corresponding mathematical model is set up.

考虑某些实际应用中直接测取往复压缩机气缸压力的不便，提出采用阀腔脉动压力替代气缸压力，未作为热力参数法的主要故障诊断信号的新思路，并通过&压力激发&将阀片运动规律、气缸工作过程和陶腔压力变化互相联系起来，建立相应的数学模型。

A new valve design is proposed by shortening stroke distance of the valve,altering motion condition im magnetic field and picking a magnetic saturated alloyof iron and nickel as the material for the valve.

经缩短阀片行程距离，改变其在磁场中运动状态，并选用IJ50较高磁饱和铁镍软磁合金为阀片材料试验。

Unscrew the Allen screw in the middle of valve cap and lift up the cap just enough to pick up the old diaphragm.

我记得前面diaogragm是翻译为阀片，这里有翻译为阀膜？？正好足够什么概念？

Under the conditions of keeping other design parameters constant, design thickness of valve flap increases with the mass increment on single wheel spring of the vehicle; throttle gap of oil-air spring is in linear decrement relationship with mass on single wheel spring. For each mass increment of 100kg on tested single wheel spring, design thickness of throttle valve flap will increase by 0.007mm and the throttle gap will decrease by 0.001mm.

在其它设计参数保持不变的情况下，阀片设计厚度随车辆单轮簧上质量的增加而增加；油气弹簧节流缝隙与单轮簧上质量成线性递减关系；试验的单轮簧上质量每增加100kg则节流阀片设计厚度将增加0.007mm，节流缝隙将减小0.001mm。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。