阀体

It has the function of correctly controlling the pressure, flame resistance and acid mist filtering when valve open and close.

阀体采用阻燃ABS材料，阀芯为柱状结构(ZL 00 2 41118.0)，双过滤酸雾滤片，具有准确控制开、闭阀压力、阻燃、过滤酸雾功能。

Hang the Air Gap Drain on the body of the relief valve Fig.

将气隙排放装置悬挂在安全阀阀体上（图2）。

As a downstream piping system when the valve opens, reflux valve, when closed, the main medium used to prevent backflow to prevent the pump and drive motor reversal, as well as a container medium discharge; currently the most commonly used is the valve flap around the body Swing Pin rotation flap valve and the valve body along the vertical axis to move lift check valve, but the above two kinds of structures exist in the valve closed, medium speed back quickly from the largest drop to zero, inlet side of the pipe resulted in the rapid pressure rise, resulting Proportional Pressure Reducing Valves in damaging effects on the piping system of water hammer phenomenon, it is generally a diameter of valve production of 50 ~ 500 mm.

止回阀作为管道系统顺流时开启，逆流时关闭的阀门，主要用于防止介质倒流，防止泵及驱动电机反转以及容器内介质泄放；目前使用最普遍的是阀瓣围绕阀体销轴旋转的旋启式止回阀和阀瓣沿着阀体垂直中心线移动的升降式止回阀，但以上2种结构的阀门均存在关闭时介质倒流速度从最大迅速降为零，致使管道进水管一侧内压迅速升高，从而产生对管路系统有破坏作用的水锤现象，所以一般止回阀生产口径为50～500 mm。

The height control valve comprises a housing defining an interior chamber and having an inlet port fluidly connecting to a source of pressurized air.

该高度控制阀包括一个形成内腔(36)的阀体(30)，阀体上有一个输入口(38)，可与压力空气源流体连通。

The most important are as follows: Detection of type: valve stem seal leakage test and test; water valve tightness test; switch tightness test; the take-off safety valve Test; Detection Object: valve, the cut-off valve , safety valve, throttle valve, check valve, swing check valve, ball valve, regulating valve and other hollow pump body, valve body and housing, etc.; way valve connection: flange connection, threaded connection, welding connection; detection medium.

最重要的有以下几种：检测类型：阀门密封性试验及阀杆泄漏性试验；水中阀体密封性试验；开关密封性试验；安全阀的起跳值试验；检测对象：闸阀、截止阀、安全阀、节流阀、止回阀、摆动式逆止阀、球阀、调节阀和其他中空的泵体、阀体和壳体等；阀门联接方式：法兰联接、螺纹连接、焊接联接；检测介质。

It make use of three-dimensional CAD parameterization designing technique to design and draw valve body mainly, and offer the database administration module of project, for finishing valve body casting technological design.

主要利用三维CAD参数化设计技术来设计绘制阀体，并提供工程数据库管理模块，以便完成阀体铸造工艺设计。

Throttle Design accord with SY/ T5127-2002, API Spec 6A sum API Spec 16C request, Points structural form Can divide into Can mode throttle and Stationary type throttle, Fixes throttle valve casing and Can transfer throttle valve casing Can exchange.

节流阀JLK、JLG系列）的设计符合SY/T5127-2002、API Spec 6A和API Spec 16C要求，按结构形式可分为可调式节流阀和固定式节流阀，固定节流阀体与可调节流阀体可以互换。

Once it is installed on the body, he was the valve cap or valve body by the sealing gasket.

一旦它被安装在阀体上，他被阀帽或阀体的垫片所密封。

Globe valves are characterized by a partition separating the two halves of the body with a center passage that is opened and closed by a screw-down/screw-up seat mounted at right angle to the body.

截止阀的特点在于阀体由部分分开的两部分组成，中心流道的开启和关闭是通过安装在阀体上某个适当角度的螺杆上升或下降来实现。

3 Open the regulator and the nozzle ring ring screw fixation screws; 1.3.4 release and remove the valve cover nut; 1.3.5 screw bolts with rings at the stem, from the valve assembly of the upper part of the body perpendicular to bring devices; when the upper part of unit from the valve body will be raised when the stem or any part not allowed to have any sway movements, any shaking could damage to the valve seat.

1.3.3 拆开调节环固定螺丝和喷咀环固定螺丝； 1.3.4 松开并拆下阀盖螺母； 1.3.5 用吊环螺栓拧在阀杆上，从阀体内垂直提起组装的上部装置；当从阀体内将上部装置提出来时，不允许阀杆或任何部件有任何的摇摆动作，任何摇动都可能损坏阀座。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。