阀体

One piece body design, top entry trunnion support with end flanges

整体式阀体设计，上装式枢轴固定支持，端法兰结构

A large trunnion or trunnion support design ensures central positioning under the highest working pressure. The trunnion mounted ball permits ease of operation.

三片式阀体设计大枢轴或枢轴板设计确保在高压下正确的中心位置，固定球结构保证阀门良好的操作性能。

Remove handwheel and turn indicator sleeve by grasping the handwheel and pulling away from the valve body along the stem.

拆卸手轮，并通过抓住手轮旋转指示器套筒，将其沿着阀杆从阀体内拉出。

It is different with the manual exhaust Slurry pumps valve is not required to run the wind man, it must be installed on the location of gas pipeline set point, the so-called water gas gathering point is the top horizontal tube of the highest point, this horizontal pipe 3 ‰ gradient requirements, does not allow for local conditions such as depression and bending, when the air into the valve, the valve automatically opens, the air removed, the water level rose, it will automatically close the valve, hot water can not spill, from a virtually eliminating Manual exhaust is not timely, easy to form a "vapor lock" effect caused by hot water heating effects and huge loss of the state.

它与手动排气闸阀不同点是不需要人为跑风，它安装的位置一定要在管路集气点上，所谓集气点就是顶层供水横管的最高点处，对此横管有3‰倾斜度要求，不允许出现局部凹陷和弯曲等情况，当空气进入阀体后，阀门会自动开启，调节阀空气排除后水位上升，它会自动关阀，热水不能外溢，从根本上消除了手动排气不及时，易形成"气阻"影响供热效果和造成热水大量流失的弊端。

Available in a choice of various body patterns including angle, straightway, left hand corner, right hand corner, vertical and vertical double union.

可提供多种阀体类型供选择，包括，角型，直线型，左侧拐角型，右侧拐角型，直立型和直立双接头型。

Do not apply wrench to body of valve.

不要将扳手应用在阀门的阀体上。

Open the valve and check X axis deviation and operation range of the valve blades.

将阀门打开同时检查 X 轴方向偏差及阀体叶片的操作范围。

According to the disc of the installation in the valve body, butterfly valve can be divided into the following forms:① centrosymmetric board.

根据蝶板在阀体中的安装方式，蝶阀可以分成以下几种形式：①中心对称板。

Alumina Bayer production desiliconization workshop, easy to coke possession of the road, easy to use separate Pressure Seal Globe Valves valve type, valve seat can be place, and carbide seal pair of DC-style cut-off valve or DC-type throttle valve.

氧化铝拜耳法生产中的脱硅车间、易结焦的管路上，易选用阀体分开式、阀座可去处的、硬质合金密封副的直流式截止阀或直流式节流阀。

The seat-carrier in multiport and diverter valves is of the Model-A design, meaning that it is not fastened to the valve body with internal threads.

多通阀和分流阀内的阀座支架是型号A结构，这意味着它不需要紧固在阀体内部螺纹上。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。