闸流管

On the basis of Gate Controlled Thyristor model, the influence of the structure of P base region on on-state characteristic is analyzed using MEDICI simulator.

在建立门极换流晶闸管器件模型基础上，利用MEDICI软件分析了P基区结构对门极换流晶闸管通态特性的影响。

It includes high power high voltage constant-current-charging system, capacitors bank, discharge control system, power supply of preignition for Xe-flashlamps, general control and diagnostic system. The power conditioning system drives flashlamps that pump the SSHCL. Flashlamps are driven by high voltage Silicon Controlled Rectifiers switched, resonant charged, discharge pulse forming network. The system uses microchip and digital circle which is based on CAN-bus for control and diagnostics. Energy diagnosis and thermal management are controlled by computers.

其中大功率高压恒流充电装置采用了L-C串联谐振电路，充电功率大，效率较高；储能装置采用了多节脉冲成形网络，可产生波形良好的强电流放电脉冲；放电控制装置采用高压大功率晶闸管，开关速度快，工作稳定；预燃与触发装置采用了开关电源电路，效率高、功耗小；总控与测量装置采用基于CAN总线的数字电路和单片机技术，控制冷却系统在激光器出光时对脉冲氙灯进行水冷，并对全系统进行控制和状态检测，同时具有过压、过流、过热等保护功能。

In recent years, cold cathode thyratron KN-22 is widely used in circuit, but here KN-22 is replaced by MOSFET. The circuit with MOSFET has stable and credible performance, it can output a pulse of -6.6～-8kV and the pulse width can be adjusted from 5ns to 10ns.

应用冷阴极闸流管KN-22作为开关线路比较广泛，但近年来我们改用MOS场效应管线路代替KN-22，该线路性能稳定可靠，输出脉冲幅度为-6.6～-8kV，脉冲宽度5～10ns可调，触发晃动小于0.5ns，触发延时30～40ns，单脉冲选出率为100%。

In the electric motor soft start question, uses the crystal thyratron intelligence module which controls by the singlechip to change the electric motor the initial firing current, the realization soft start; In the protection question, uses the singlechip to monitor the electric motor the movement, to lacks the breakdown implementation to separate the electrical machinery movement immediately, according to certain algorithm judgment electric motor whether crosses the class, like tallies has flowed the condition is the separation electrical machinery movement.

在电动机软起动问题上，采用由单片机控制的晶闸管智能模块改变电动机的起动电流，实现软起动；在保护问题上，采用单片机监视电动机的运行，对缺相故障实行立即断开电机运行，根据一定算法判断电动机是否过流，如符合过流条件即断开电机运行。

Thyratron ; sieving method ; detonating circuit

闸流管；筛选方法；起爆电路

Pulse modulator ; thyratron ; repetition rate

脉冲调节器；闸流管；重复率

The use of thyris to r valves has increased the reliability of HVDC converters to impressive levels.

晶闸管换流阀的采用已将高压直流换流器的可靠性提高到相当惊人的水平。

This method is more practical to the sieving of the thyratrons used in fuze detonating circuits.

这种方法对引信起爆电路用闸流管的检测更具有实际意义

The limit temperature of the thyristors will be reached.

半导体闸流管的极限温度可以被达到。

First, by the allocation of irrigation water directly into the ditch outlet Xiaqi, achieve no water loss, greatly improve the utilization of water; are two irrigation systems, replace the pipe with water furrow, not square, and the right to re-use, reducing the irrigation investment; Three is the use of the gate with the outlet opening to adjust a constant and accurate control of flow into the trench plot, for different soil and different groove specifications Xiaqi can greatly improve irrigation uniformity; four gates are porous pipe irrigation system for the flow tubes, and the blind to cross the flow tube as compared to the wall can reduce the work under stress, and reduce the damage to the opportunity to prolong the service life of thin-walled tube; are five gates to facilitate the installation of irrigation systems, pipes, and, upon request, to fight孔安outlet assembly to ensure the accuracy of positioning with the outlet.

一是灌溉水经配水口直接进入沟畦，实现无输水损失，极大地提高了水的利用率；二是管灌溉系统代替配水垄沟，不占地，且右重复使用，降低了灌溉投资；三是利用配水口的闸板开度来调节准确恒定地控制进入沟畦的流量，适用于不同土质和规格不同的沟畦，可大大提高灌水均匀度；四是闸管灌溉系统为多孔出流管，与等过流量的盲管相比，可降低管壁承受的工作压力，并减少受损机会，从而延长薄壁管的使用寿命；五是闸管灌溉系统安装方便，并可根据要求打孔安装配水口，确保配水口定位的准确性。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐