间隙的

Toptie Welds already designed and produced the narrow gap welding machine, mechanical saddle joint welding machine, numerical controlled saddle joint welding machine, saddle hole cutting machine and strip overlaying subarc welding machine and so on. Those had already applied in some famous pressure vessel and boiler producer successfully and gained consistent appraise.

公司目前已有深坡口窄间隙埋弧焊机、机械马鞍形埋弧焊机系列、数控马鞍形埋弧焊机系列、马鞍形管孔切割机、埋弧带极堆焊等系列产品，并已在国内外著名压力容器、锅炉企业成功投入使用，获得客户的一致好评。

Blood-brain barrier in tumors and peritumoral oedematous regions had the same variations in ultrastructure.

瘤体和瘤周水肿区血脑屏障超微结构变化无明显差异，内皮肿胀，毛细血管腔狭小，胶面有稀疏的绒毛样突起，内皮为无孔型，胞质内胞饮泡较多，内皮紧密连接增长，细胞连接间隙增宽，基膜完整，胶质膜缺损。

The vibrations are caused by spindle curved tooth meshing impact when the gap between work roller bearing block and frame is oversized.

主要振因是当工作辊轴承座与牌坊之间间隙过大时，接轴弧形齿的啮合冲击将激起轧辊横向振动。

The control system by microcomputer for tandem wire narrow gap SAW machine is solved adopting 80C196 monolithic computer.

采用80C196单片机为控制核心，解决了窄间隙埋弧焊机的微机控制问题。

It can be found that multi-grade oil can be applied in wider temperature scope than single grade oil. When the inlet temperature is high, it is better not to use the winter oil.

利用快速解法全面考察了轴承相对间隙、轴承宽度和直径以及供油槽位置和长度对轴承润滑性能的影响。

Confirm the clearance between the wind box and the scraper for non-touching in each direction.

确保进风管与刮板之间的间隙，以免导致摩擦。

First of all, horizontal swing to solve big problems, re-allocation of a motor sleeve (with the bronze with stent hole so), so that the electrical sleeve just in bronze wall bracket can rotate, reducing the gap; further axial movement to solve the problem with the motor shaft with Hexagon Hexagon washer so thick 0.6mm.

首先解决横向摆动大的问题，重新配做一个电机轴套，使电机轴套在铸铜支架内壁刚好能转动，减小间隙；再解决轴向窜动问题，与内六角电机轴配做内六角垫圈，厚0.6mm。

Based on the experiment of twin-wire narrow gap welding in single pool mode by employing alternative pulsed arcs, the influences of welding parameters on the appearance of weld and welding process stability were investigated.

采用交替脉冲，对双丝共熔池窄间隙焊进行工艺试验，研究了焊接参数对焊缝成形和电弧稳定性的影响。

Lateral oscillation arc welding, high-speed-rotating arc welding, twin-wire welding, and ultra NGW can all assure the fusion of side wall and improve the oppearance of weld in relatively small welding variables.

横向摆动电弧、高速旋转电弧、双丝焊和超窄间隙焊4类方式都可以在较小的焊接规范下，保证侧壁熔合，改善焊缝成形，防止焊接裂纹。

While an 88-N proximal traction force was applied to tension the graft, it was fixed in the fibular head tunnel with a 7 mm 23 mm bioabsorbable screw while the knee was flexed to 30, in neutral rotation, and with a valgus force applied to reduce any potential lateral compartment gapping.

施加约88N的牵引力拉紧移植物，在膝关节屈曲30°、旋转中立位、施加内翻力降低任何潜在外侧室间隙时用7mmX23mm生物可吸收螺钉固定于腓骨头隧道。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。