间隙的

Since pain generators are located anteriorly in the epiduralspace, ventral epidural spread is the logical target for placementof antiinflammatory medications.

因为疼痛的起源位于硬膜外间隙的前面，在硬膜外间隙中向腹侧弥散是抗炎药物布局的合理目标。

CT sign of fascial space infection included effacement of fat and swelling of the adjacent tissues, disruption of platysm, faseial enhancement, fluid and gas collection were found in 2 necrotic fasciitis.

同时，通过对颈部感染在颈部筋膜间隙中蔓延的CT表现进行分析，可以对颈部筋膜及其间隙的解剖进行更深入的研究。

It is directive for precautions on windage discharge and as a reference for transmission line designing.

选择有代表性的间隙和工况进行雨水条件下导线-杆塔操作冲击闪络试验，得出了空气间隙的冲击闪络特性的变化规律，为现场防风偏放电和输电线路设计提供理论指导。

Sectional anatomy of the infratemporal space has important clinical significance for imaging diagnosis of tumors in the infratemporal space.

颞下间隙的横断层解剖对颞下间隙肿瘤等疾病的影像诊断具有重要临床意义。

In addition, author also concludes the formulation of the clearance in radius direction and normal direction for all kinds of nonparallel degree between input shaft and output shaft.

并得出了两齿轮传动轴在各种不平行度下的径向间隙和法向间隙的计算公式。

Methods Fifteen cadaveric heads were taken in this study. The arteries and veins of the heads were perfused with red and blue latex, respectively, for simulating pterion approach under microscope. The spatial relationship between the anterior segment of basal vein and the operation space was examined. The cranium was then removed, the basal vein and its branches were observed and measured in the free brain.

取15具（30侧）尸头标本，动、静脉分别用红、蓝色乳胶灌注，在显微镜下模拟翼点手术入路，分别从手术中常用的间隙进行操作，观察基底静脉前段与手术间隙的关系。

Objective To study the interspace lateral to internal carotid artery, observe and measure the boundary, area and different content in the interspaces under different visual angles.

目的：经翼点入路不同视角下对颈内动脉外侧间隙进行显微解剖学研究，确定该手术间隙的界限、大小及不同视角下其内重要结构的显示程度及临床意义。

The results of simulation studies indicate that setting of earth-fault distance protection on sectionalized groundwire with gap should be calculated on all the gaps disruptive flashover.

在此基础上，提出了接地距离保护在地线分段带间隙的线路上宜按所有间隙都击穿情况下的阻抗参数进行整定的建议。

When machining parts with bore as positioning reference, if clearance fit positioning is adopted, machining accuracy is certainly affected due to the existence of clearance.

在精加工以内孔为定位基准的零件时，所用芯轴类工装如果采用间隙配合定位，由于定位间隙的存在，必然影响零件的加工精度。

Tests were carried out using ±1 000 kV simulation tower in this paper, and switching impulse and lightning impulse flashover characteristic curves of typical air gap in ±1 000 kV transmission tower were obtained. These curves were compared with test results of ±500 and ±800 kV air gap, and the flashover characteristic of 750 kV AC transmission tower and square tower window were also discussed in this paper.

利用±1 000 kV模拟塔头进行试验，得到了±1 000 kV杆塔典型空气间隙的操作冲击和雷电冲击放电特性曲线，并与±500和±800 kV杆塔塔头的空气间隙研究成果进行对比分析，同时结合750 kV 交流杆塔塔头和正方形塔窗的操作冲击特性进行了讨论和分析。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。