间隙的

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skilled welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

Flat Welding : choice of welding technology, electrode diameter, welding current, welding speed, the length of arc welding, weld process verification; Welding : welding inspection clearance groove, assembly space whether it meets the requirements, positioning it firmly welding, weld around is not oil, rust; Electrode temperature and baking time should be required, the rod removed from the oven. tempreture-constant drum on the electrode, then used as admission; Latin America : welding supply welding thickness, welding levels and electrode type and diameter, skil led welders and other factors, and to select appropriate welding current; fillet weld arc : fluctuations in the point arc weld end, they are advised more than 10 mm, is not hard arc, sparking arc weld zone from the electrode should be started immediately. Component integration and maintaining so-rod pieces have 2-4 mm gap arc.

1.1.2.1平焊：选择合适的焊接工艺，焊条直径，焊接电流，焊接速度，焊接电弧长度等，通过焊接工艺验证；清理焊口：焊前检查坡口、组装间隙是否符合要求，定位焊是否牢固，焊缝周围不得有油污、锈物；烘焙焊条应符合规定温度与时间，从烘箱中取出的焊条，放在焊条保温桶内，随用随取；焊拉电源：根据焊件厚度、焊接层次、焊条型号、直径、焊工熟练程度等因素，选择适宜的焊接电流；引弧：角焊缝起落弧点应在焊缝端部，宜大于10㎜，不应随便打弧，打火引弧后应立即将焊条从焊缝区拉开，使焊条块结合与构件间保持2～4㎜间隙产生电弧。

By taking two typical uncontrolled crosswalks in Beijing as examples, a traffic investigation was made. Then, the critical crossing gap of pedestrian, the probability of safely crossing the gap and the total delay time of pedestrian were computed.

以北京市两个典型无信号控制人行横道为实例进行交通调查分析，计算行人的临界穿越间隙，安全穿越间隙出现的概率，及行人穿越该处的总延误时间。

Import and pump impeller shell gap between the pump over the General Assembly high-pressure area caused by water flow through the gap area of low pressure affected the water pump, efficiency!

叶轮进口与泵壳间的间隙过大会造成泵内高压区的水经此间隙流向低压区，影响泵的出水量，效率降低！

The occurrence of wrinkling is attributed to the large die gap, which is the difference between the side length of the die cavity opening and the side length of the punch head.

出现的皱折是由于模具间隙大引起的；该间隙在模具腔口的侧面距离和冲头侧面距离之间有差别。

In order to examine the effect of die gap on the wrinkling, the stamping of a tapered square cup with three different die gaps of 20 mm, 30 mm, and 50 mm was simulated. In each simulation, the die cavity opening is fixed at 200 mm, and the cup is drawn to the same height of 100 mm.

为了验证模具间隙对起皱的影响，模拟了一个在从20MM， 30MM和50MM不同模具间隙下的锥形方杯的冲压，在每次仿真中，模腔打开固定在200MM，杯形拉伸同样高度100MM。

The clearance after crystal is muddy: The clearance after crystal is the cavity of one layer optics after crystal center is straight, the forehead that funnel state vitreous body is in charge of is in the center of, namely the forehead of primitive vitreous body.

晶体后间隙混浊：晶体后间隙为晶体中心直后的一薄层光学空腔，中央为漏斗状玻璃体管的前部，即原始玻璃体的前部。

Careful treatment can decrease the complication rate. 3. Three-dimensional finite element model analysis showed that zygomaticoalveolar crest is the major site sustaining stress, which indicated that the fixation of zygomaticoalveolar crest should be strengthened, if there is some space between zygomaticoalveolar crest and fibula bone, free bone graft can fill the space to rebuild the bony zygomatic process support.

游离腓骨复合组织瓣上颌骨重建的三维有限元分析表明，颧牙槽嵴部位是腓骨瓣上颌骨重建后咀嚼压力的主要受力部位，提示腓骨瓣上颌骨重建时要加强颧牙槽嵴的固定；当上颌骨切除后腓骨与颧牙槽嵴存在间隙时，应尽量采取游离骨块移植，充填间隙，重建骨性颧突支柱。

Because of the effects of particle posterities and gas distributor, there is another particular axial distribution of cross-sectional averaged solids holdups, in which the averaged holdups increase first and then decreases along the riser height.

采用间隙指数定量描述了气固混合程度，结果表明整个提升管内没有形成很明显的絮状物，局部流动比较稳定；在相同Gs1.2/Gg2.0条件下，间隙指数在确定的提升管截面上有较为一致的径向分布规律。

The properties are the dispersion equation of IREBs drifting in the tube, and the transmission line model of IREBs interacting with the gap electrical field of input cavity of RKA and bunching in the drift tube. The expression of modulated current after the gap of input cavity is got, which is content with the experimental results.

建立了IREBs在漂移管中传输的色散方程，以及IREBs与RKA输入腔间隙电场相互作用和IREBs在漂移管中群聚传输的传输线模型，获得了电子束经过输入腔间隙后产生的调制电流表达式。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新