间隙的

Relationship between butt joint gap and cold crack rate of 16 Mn steel underwater wet welding is studied.

研究了水下湿法焊对接接头间隙与裂纹率的关系。随着接头间隙的增大，裂纹率逐渐减少。

A fuzzy controller was designed,of which the inputs were the force error and the change of force error which was transfered from the error of interelectrode gap by using another BP NN which was trained by the pair of the gap-force data gathered in the test, the output of controller was the increment of feed velocity.

与阴阳极间间隙的关系；采集电解加工过程中阴极表面上的力信号，经过信号处理后用其训练一个BP神经网络，实现间隙的在线检测；设计了一个模糊控制器，把间隙的误差转化为力的误差，将误差的变化信号作为模糊控制器的输入，将进给速度的增量作为模糊控制器输出。

One of two magnetic rings is fixed and the other can move axially.Because of the function of magnetic field,two magnetic rings keep each other with a due distance axially.

在磁场作用下，两环自动保持一定的轴向间隙，任何外力作用下此间隙的改变会产生一个恢复力，即弹力。

The first one is to generate the circle for each borderline segment of the component by considering the segment length and the prescribed tolerance value. If this is not the case, the borderline segment will be equally divided into halves until the obtained circle satisfies the tolerance value over the whole borderlines of the component. The basic idea of the last two algorithms aims at covering the domain occupied by the component as much as possible. The circle generation is carried out sequentially from salient angle to the sector formed by the salient angle till the uncovered borderline segments of the component. Particularly, the three-step algorithm with gap allows that the generated circles are distributed with gap along the component contour.

二分法利用组件各边长度和设置的容差大小得到该边的候选包络圆，若该圆不满足组件所有边的容差要求，则将该边不断地对分，直至所得到的包络圆满足各边的容差要求；三步划分法和带间隙的改进三步划分法则以组件区域为划分对象，依次对组件多边形凸顶角、凸扇形区和多边形各边剩余线段划分包络圆，且带间隙的改进三步划分法则允许包络圆在组件边界上以适当的间隙分布。

Parapharyngeal space was divided into two parts by the line from styloid process to pharyngeal recess;preparapharyngeal and retroparapharyngeal space,It was better to show relationship of structures in the retroparapharyngeal space with CT.

但关于咽旁间隙的CT影像解剖，尤其是定量研究资料尚较缺乏，为此笔者在CT图像上对咽旁间隙及咽旁结构进行了观察、测量，以期为此区疾病的影像诊断提供解剖学资料。1 材料和方法在GE980 0型CT机上，沿眶耳线向下连续扫描，层厚 5mm。

Based on the model,the relationship between the main pulse frequency of supply power and the balanceable inter-electrode gap is discussed.

给出了脉冲电化学加工极间平衡间隙的数学模型，并据此讨论了高频群脉冲电化学加工中，电源主脉冲频率与平衡加工间隙的关系。

They put forward that a new concept of open /closed compound pair,which is not only used to renewably synthesize restrict mechanism of bearing stand chock about aluminum foil mil...

提出开闭复合运动副新概念，重新综合铝箔轧机轴承座约束机构，解决了该轧机工作辊轴承座与机架窗口间更换轧辊必留间隙和在运行时须消除间隙的矛盾。

The clearance cause more serious effect on the response of turret than that of the rotary table. This result agrees with the experimental response of roller gear indexing cam mechanism. In addition, some problems, such as the impacts on mechanism with clearance, effect on response for preload, effect for inertia of rotary table and stiffness of output-shaft, effect on wave of velocity and torsion for motor characteristic, and so on are investigated.

通过对扭转动力学模型的计算还对以下问题进行了研究：间隙造成的横越冲击的表现；预紧的存在对响应的影响；间隙的存在对有廓形误差的凸轮机构的动力学响应的影响；分度盘轴的刚度和载荷盘惯量对含间隙分度凸轮机构响应的影响；电机特性对转速波动和扭矩波动的影响等等。

Adjustment of the countertop with the seams of the wall: when the benchmark side of the countertop joints with the jointing side, in case the clearance between splash back of the countertop and the wall is larger than 5MM, use the following method to adjust.

台面与墙面缝隙的调整：接驳台面基准边与对接边合拢后，对于非直角墙体，如台面挡水与墙体面缝隙超过5MM，我们可以通过下面的方法调整，将两块台面紧靠墙，将两块台面的后挡水边靠拢在一起，这时两块台面的前端有间隙，就用卷尺测量前端间隙的尺寸，在后挡水处按间隙尺寸做标记，连接前端点和后面的标记划线。

Adjustment of the countertop with the seams of the wall: when the benchmark side of the countertop joints with the jointing side, in case the clearance between splash back of the countertop and the wall is larger than 5MM, use the following method to adjust. Place the two countertops tightly against thewall and put the two splashes back together. In this way, the two countertops will have clearance at the front side. Measure the clearance of the front and mark the clearance dimensions at the splash back. Mark along the front end and marks at splash back. Cut along the line.

台面与墙面缝隙的调整：接驳台面基准边与对接边合拢后，对于非直角墙体，如台面挡水与墙体面缝隙超过5MM，我们可以通过下面的方法调整，将两块台面紧靠墙，将两块台面的后挡水边靠拢在一起，这时两块台面的前端有间隙，就用卷尺测量前端间隙的尺寸，在后挡水处按间隙尺寸做标记，连接前端点和后面的标记划线。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了