间隙的

There have been many good results when M is minimal sub manifold. In the first section we will introduce the context and make a general description on the recent researches. In the second we will introduce the complexion of the development for this problem. In the fourth we\'ll discuss the second gap on special conditions using similar methods when the mean curvature is constant, and find the second gap.

关于极小子流形的间隙问题已经有了很多好的结果，第一节引言中我们将介绍本文的研究背景及这些主要结果，第二节中我们来介绍具有常平均曲率情形的间隙问题的发展现状，在第四节中我们用类似的方法讨论平均曲率为常数的紧致超曲面的第二间隙问题，得到了第二间隙δ=？

If you bend down, you can reduce this bending parts of teeth pad and nano-imprint lithography drum of gaps can be reduced by this bending parts of clishion and siowal paper teeth to feed of the top of the gap; if the multiplicable this bending parts of teeth pad and nano-imprint lithography drum of gaps could be increased by the curved parts of clishion and siowal paper teeth to feed the gap.

如果往下笔直，可裁减此笔直部位的递纸牙垫与压印滚筒的间隙，也可裁减此笔直部位递纸牙垫与给纸台的间隙；如果往上笔直，可补充此笔直部位的递纸牙垫与压印滚筒的间隙，也可补充此笔直部位递纸牙垫与给纸台的间隙。

Anterior and posterior parapharyngeal space were determined by a line between the styloid process and the pharyngeal recess, anatomical structures of the posterior parapharyngeal space and their relations could be better displayed on CT images.

自茎突至咽隐窝的连线将咽旁间隙分为咽旁前、后间隙，CT图像能较好显示咽旁后间隙内各结构的相互关系。

Watch the space δ that from the brake shoe to guiding track; should from 3 to 5mm, and the space of 4 brake shoe should be the same, if not, adjust the components.

4.5.3。首先察看楔块闸皮至导轨管臂间的间隙δ；一般要求应在3－5毫米之间，且4块闸皮间隙均等，如果不一样，通过调节组合件，使得各楔块间隙均等

Figure 1: Relationship between the width of the buccal channel and resistance to flow of saliva: left: wide channel, rapid flow, poor retention; right: narrow channel, slow flow, good retention After Basker,R.M.

图1：颊侧间隙宽度与抵抗唾液流动的关系：左：间隙宽，流速快，固位差；右：间隙窄，流速慢，固位好。

All cases were given debridement, and changed the pattern of fracture fixation or adjusting the position of outer fixation device. Then the VAC was applied in a region- and layer-wise manner in the intermuscular space, interjoint space and the interfracture space., The sequential and time of tube withdrawal was decided by tube position and drainage pattern. with drainage changes every 5~7 days according to the drainage state. The drainage were applied 1~4 times per case, averaging out at 2.2 times.

所有病例均先行清创，更换骨折固定类型或调整外固定架固定位置，在感染的肌肉间隙、关节间隙、骨折间隙等分区应用、分层应用VAC，并根据置管部位和引流情况决定拔管次序和时间， 5～7天根据引流情况进行更换引流装置，应用次数为1～4次/例，平均2.2次/例。

Additionally, cross section curve of helix wire, contact radius, clearance angle, width and ratio in wires same layer were obtained.

为了掌握轴向载荷下螺旋钢丝的变形特性以合理设计钢丝绳，推导了螺旋钢丝轴应变显式表达式，给出了螺旋钢丝截面曲线表达式和同层螺旋钢丝正好满足接触时钢丝的半径及接触半径、间隙角、间隙值和间隙率表达式。

In order to design reliable wire ropes by investigating the deformation characteristics of wires helix, axial strain's explicit expressions and radius' expressions of wires helix were deduced in which wires were bearing axial load and just touching each other. Additionally, cross section curve of helix wire, contact radius, clearance angle, width and ratio in wires' same layer were obtained.

为了掌握轴向载荷下螺旋钢丝的变形特性以合理设计钢丝绳，推导了螺旋钢丝轴应变显式表达式，给出了螺旋钢丝截面曲线表达式和同层螺旋钢丝正好满足接触时钢丝的半径及接触半径、间隙角、间隙值和间隙率表达式。

The application of the gap element method in gap joint mechanisms is proposed. The stiffness matrix of the rotate joint elements and sleeve joint elements with gap elements are formed and the dynamic equation of the structure is given in the paper.

文中还提出了旋转铰和滑移铰两种间隙单元，推导了间隙单元的刚度矩阵，最后给出了含间隙单元的结构动力学方程。

If there is no excessive wear or the time gap, they should check: First, the steering gear worm gear wear, or the required space, such as the gap is too large to be adjusted; Second, the shift device connected part of the wear and tear, or whether or not to adjust too loose; Third, the steering is loose parts installed; Fourth, there are loose steering arm down.

如无过大磨损或间隙时，则应检查：第一，转向器蜗轮蜗杆磨损情况，或间隙是否符合规定，如间隙过大应调整；第二，转向装置连接部分的磨损情况，或是否调整得过松；第三，转向器安装部位是否松动；第四，转向垂臂有松动。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。