间隙

A few epidermal hairs distributed on the Costa of Lonicera Japonica Thumb. The upper epidermis of Solidago decurrens Lour were covered with sparse stellate hairs. The stomas distributed on the upper epidermis hairs of Lonicera Japonica Thunb, Lonicera confuse and Solidago decurrens Lour, which could reflect the sunlight and decrease the transpiration to adapt the highlight and drought environment;(2) The leaf blades of Polygala japonica butt were fleshy, and the sunk stomas distributed on both the sunk place of the upper epidermis and lower epidermis, which help to water conservation.

结果：(1)忍冬、华南忍冬、黄花草下表皮均分布浓密的表皮毛，忍冬上表面中脉有少量表皮毛，黄花草上表皮分布有稀疏的星状表皮毛，忍冬、华南忍冬和黄花草的气孔位于下表皮毛间隙，这种结构可反射阳光和阻止水分蒸发，从而适应强光和水分不足的环境；(2)瓜子金叶片为肉质叶，上下表面均有气孔分布，并出现明显的下陷。

Therefore, the leakage control technology of air preheater becomes an important problem that must be solved.

因此空预器的密封间隙控制技术是该领域的一个研究热点。

In this thesis, several advanced control methods are adopted to improve the performance of the traditional air preheater leakage control system using non-touched sensor.

本文采用了多种先进控制方法，用来改进传统的非接触式空气预热器密封间隙控制系统。

As matches pairs of bearings, preload for them is more convenient.

成对使用时，以预先调整好间隙的配对角接触球轴承最为方便。

Interference fit: results in an interference between the two assembled parts--the shaft is larger than the hole, requiring a force or press fit, an effect similar to welding the two parts.

过度配合：在两个装配在一起的零件之间或者存在着过盈，或者存在着间隙的配合——轴可以小于或大于孔，但仍在规定的公差内。

In this paper, we propose a general model of a class of Lagrangian dual problem for the general nonlinear programming problem with respect to some Lagrange-type functions. We obtain that the zero duality gap exists between this class of Lagrangian dual problem and the primal problem.

针对一般的非线性规划问题，利用某些Lagrange型函数给出了一类Lagrangian对偶问题的一般模型，并证明它与原问题之间存在零对偶间隙。

The ignition of this electric current in the regulation when the dot is released with onefold weaveform, and the primary coil that electric current has shed ignition coil, tall voltage electricity produces in the secondary coil induction of ignition coil, its are to be in as a result intense scintilla bursts forth in sparkplug clearance.

此电流在规定的点火正时点以单一的波形被释放，而电流流过点火线圈的初级线圈，在点火线圈的次级线圈感应产生高电压电流，其结果是在火花塞间隙中迸发强烈的火花。

In order to compare the results for the three different die gaps, the ratio of the two principal strains is introduced, being min/max, where max and min are the major and the minor principal strains, respectively. Hosford and Caddell [5] have shown that if the absolute value of is greater than a critical value, wrinkling is supposed to occur, and the larger the absolute value of , the greater is the possibility of wrinkling.

为了比较三种不同模具间隙的结果，两种主要张力的比率被介绍-是最小值/最大值，这里最小值/最大值是主要的和次要的张力，分别的， Hosford and Caddell [5] 显示如果他的绝对值比临界值大，起皱应该会产生，越大的绝对值，则越大的起皱产生。

The optimized processing parameters including screen print and hot pressing were obtained. In order to reduce error, the method of double-face screen print in key electrode layer and stepped press were used. Ceramics are dense after sintering. The thickness of electrode is about 5μm. The test fixtures based on microstripe for SMD were design and fabricated.

采用平面电感和平板电容结构实现的LC谐振器，由于集总电感的Q值较小以及高介电常数介质基片杂散参数效应，这种结构的谐振器Q值较小；采用新的耦合结构-间隙电容耦合结构，实现谐振器和外电路的匹配耦合，使谐振器和耦合电容在同一层上实现，即单层结构，和传统的平行板电容耦合方式相比减小了耦合电容对位误差。

The influence of the required quality of prismatic joints to achieve guaranteed cleance and strength was a speciality problem.

棱形联接接头的尺寸和配合精度对保证接头中孔轴之间的间隙，以及各自的机械强度有着非常重要的影响。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。