间距

We know that every new paper weight regardless of type, has a certain degree of thickness, when a piece of paper folding times a little while and page number spacing error; when all the foldedthe of the final book in a manner worthy of piled up and preparation to become a book condrctor, on the accuracy of it.

我们知道，每一种纸张不论种类、克重都有一定的厚度，当一张纸折叠次数不多时，页码间距误差不大；当所有折好的书帖最后采用叠配法成为一本书芯时，对精度的影响也不大。

The lift course of hanging device on wheat no-tillage planter was simulated by using the software of ADAMS. Some important parameters were obtained such as height of the working part relative to ground, the distance between the working part and the rear wheel of tractor, the angle of road pass and the force of hanging point, etc. The key parameters of the hanging device and its best working parameter of hanging device were found out through optimization simulation. Simulation results showed that suspension point had minimum force when variable DV_1 and DV_2 gained corresponding maximum and minimum at scope of structure limit.

应用ADAMS软件对小麦免耕播种机悬挂机构提升过程进行了动态仿真，得到了工作部件的位置高度、工作部件与拖拉机后轮之间的间距、路面通过角以及悬挂点的受力等参数，找到了悬挂机构的关键参数，通过优化仿真，得到了悬挂机构的最佳工作参数，仿真结果表明，设计变量DV_2、DV_3在结构受限范围内分别取其最大值和最小值，悬挂机构悬挂点受力最小。

The MnO2 nanosheet colloid suspension was poured into an arginine solution of pH＝4.0～11.0 followed by stirring for 2 d, then arginine intercalated layered manganese oxide nanocomposite with a basal spacing of 1.49 nm was prepared by a delamination/reassembling process.

剥离的MnO2纳米层胶体分散液在pH＝4.0～11.0的精氨酸溶液中搅拌2 d，得到了层间距为1.49 nm的精氨酸插层氧化锰纳米结构材料。

With a constant space and different duty ratios, two conditions with high heat transfer performances emerged mainly due to the different degrees of influence of the heat transfer surface area and the rib thickness on the heat exchange performance.

以换热系数进行比较，当占空比为83％左右时，热沉表面温度最低，换热性能最佳；当间距恒定不变而占空比不同时，会出现两个换热性能较好的情况，主要是由于换热表面积和肋片厚度影响换热性能的程度不同。

Results: Multiple regression model analysis revealed significant effects of all grip related factors such as pen grip style, direction of penpoint and distance between penpoint and pen holding point on writing speed via complex interrelationship with each other and other non grip related variables.

结果︰多重回归模式分析结果显示所有握笔相关特徵(例如握笔方式、笔尖方向以及笔尖与握笔点间距)都可能对书写速度有显著影响效果，并藉由复杂相互关系与其他变项共同产生影响效果。

This research is concentrated on the interactive behavior between the cold-formed steel wall stud and sheathing. Three kind of test specimens used in this study includes:(1) both stud and calcium silicate board are under compression;(2) the stud sheathed with calcium silicate board is under compression; and (3) the calcium silicate board supported by stud is under compression. Three different thicknesses of calcium silicate board and three different spacing of the connecting screw were adopted in the test. Totally, 36 specimens were tested in this research.

本研究乃针对冷轧型钢墙体立柱与外覆材产生束制的能力进行探讨，实验所采用的试体分为三种，具外覆材之墙体、具外覆材支撑之立柱、外覆材受压内含支撑之立柱，并配合不同厚度之矽酸钙板与改变不同螺丝间距进行互相比较，共进行了36组试验。

In addition he lengthened the old transverse springs, mounted them ahead of the front axle and behind the rear axle, stretching the spring base to 123 in. but retaining the old 112-in.

此外他还加长了原先的横置弹簧，把它们分别装在前轴的前面和后轴的后面，把间距增加到了123英寸，但保留了原先112英寸的轴距。

In addition he lengthened the old transverse springs, mounted them ahead of the front axle and behind the rear axle, stretching the spring base to 123 in. but retaining the old 112-in. wheelbase.

此外他还加长了原先的横置弹簧，把它们分别装在前轴的前面和后轴的后面，把间距增加到了123英寸，但保留了原先112英寸的轴距。

For the ChengChao Iron Mine, the space is calculated by the formula and optimal selected by the FAHP. The result of the calculation is certified by the practice to be true.

运用本论文的研究成果对程潮铁矿所采用的中段穿脉间距进行了优化计算，并运用模糊层次分析法进行了方案优选，经现场实际应用证明其计算结果是正确的，符合现场实际。

If all overprinter is in tune, but the space between the picture error is large, will also give smart label business card printing and membership card after compound and die-cutting process causing trouble.

如果每个画面都套印很准，但是画面之间的间距爆发差错较不小，也会给智能标签制卡和会员卡制作后的不简单和模切工序变成便当。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。