间距

The distance of separation of the palatine bone and maxilla was 10 to 15cm.

X线片显示，牵张侧腭横缝前后两点汞齐标志的间距增加1？5cm；

Discusses the design of coil spaces, and compares the floor panel heating system with the general radiant heating system in construction cost.

讨论了地板辐射供暖盘管间距的大小，并将地板辐射供暖系统与常规的散热器供暖系统在工程造价上进行了对比。

Results:X-ray Barium Enema findings of AMC:No filled appendical image;widening the interval up to 2cm～3cm and forming 40～55 angles between the end of ileum and the cecum;there were half-moon impressions on the cecal paries medialis and/or the paries lateral of the end of the ileum;CT findings of AMC There were...

结果 ：AMC钡肠X线征象：阑尾不显影；盲肠与回肠末端间距增宽达 2cm～ 3cm ，并形成 4 0～ 5 5度夹角；盲肠内侧壁或/和回肠外侧壁半弧形压迹，形态固定；AMC的CT征象；右髂窝区"多个"囊性病灶，呈圆形和索条状；囊壁光滑；病灶周围结构清晰。

The path space was one of the reasons that affected the precision of parts in the rapid prototyping based welding.

熔焊成型中多道焊缝路径间距是影响零件成型精度的原因。

The results show that the interlamellar spacing of pearlite is decreased progressively during the cold drawing.

试验结果表明，随着拉拔变形应变量的增大，珠光体片层间距逐渐减小，钢丝强度随之升高。

An effective method to detect the size and shape of the pectination object is introduced.

通过公式可以快速地计算出梳状体的齿宽和齿间距。

The method is :there are two perpendicular axes whose distance are controlled ,one is the axis of work table, the other is fixed with a microscope for aiming.

该测量方法是：两个相互垂直且间距可调的数控回转轴，一轴与工件的回转中心重合，另一轴上固定可移动的瞄准显微镜，当显微镜瞄准被测孔时，两轴的转角由各自的圆光栅测出，两轴之间的角度位置确定曲面壳体零件上小孔的孔位置，同时采用CCD摄像头，利用图象处理技术实现小孔的尺寸测量。

A 4.2–5 GHz, low phase noise LC-VCO with constant bandwidth and small tuning gain

一个4.2至5吉赫兹，低相位噪声，低调谐增益，等子频带间距的电感电容型压控振荡器

Three photolithographic masks are utilized in the fabrication process.SEM images show that the microprobe is 1.2mm long,100μm wide,and 30μm thick,with recording sites spaced 200μm apart for good signal isolation.

在整个工艺制作过程中需要三步光刻，制作的硅针长1.2mm，宽100μm，厚30μm，同时各个记录点的间距为200μm，可以形成良好的信号隔离。

In this way, a complete set of rapid construction technology is established, by means of which the huge deformation of the soft phyllite ground under high stress conditions can be effectively controlled.

着重介绍了乌鞘岭隧道岭脊段控制千枚岩大变形的快速施工指导思想、施工方法、施工工序、各工序标准耗时及各工序间距控制标准。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。