间距

The evaporation fields of metal atoms in the STM configuration have been calculated on the base of the binding energy of the atom on the tip, the total ionization energy of the atom, surface work function, the atomic radius and tip-sample distance.

本文的理论计算表明所需的外加电场强度决定于针尖原子的结合能，原子总的离化能，表面功函数，原子直径以及针尖和样品间距等。

Based on the Miedema′s theory of electric charge shift,a modification of Mo-reen′s model of prediction of the lattice parameters in solid solution was approachedfrom the idea of the atomic size and separation in solid solution changing withsolute concentration.

根据Miedema电荷迁移理论，引入固溶体中原子尺寸和间距随溶质浓度改变的观念，修正了Moreen的固溶体品格常数预测模型。

Autorotation involves a controlled descent with the rotor in low pitch to keep it spinning.

自动旋转涉及与转子间距控制在低后裔保持它旋转。

This will help determine foot spacing front to back.

这将有助于确定前后脚的间距。

According to the model, the deflection and main pre-brace parameters are illustrated with the Jinsong station of the tenth line in Beijing. It demonstrates that the curve shape of theoretical result, computing result and the on-set measure result are uniform in the main and the change law is similar; that the circumferential space of pipe-roof has a optimum value while satisfying the pre-brace function; that the relation between diameter of steel pipe and flexibility of barrel vault meets negative exponential function. And the diameter of steel pipe has a optimum value.

依据该模型，以北京地铁10号线劲松车站管棚支护为例，着重对管棚的挠度和主要支护参数进行的分析表明：理论结果与计算结果和现场量测结果的曲线形状基本相同，变化规律相似；在满足预支护作用的同时，存在相对较优的管棚环向间距；钢管直径与管棚挠度之间符合负指数函数关系，管径存在最佳值。

The simulation revealed the influence of the bas-relief and elbows on the flow flied and phase distribution, and the impact of the bas-relief height, width, intervals and slope angle on the flow flied.

通过模拟计算考察了浮雕结构和弯曲对流动及相分布的影响，以及浮雕结构的高度、宽度、间距和倾斜角度对流动的影响。

If you have modified any sources in the new "spaced" folder, all those changes will be lost on the next update'.

如果你已修改的新的"间距"文件夹的任何消息，所有这些变化都将丢失的下一次更新'。

The theoretical analysis and optimizing design were implemented to the structuralparameters of major working components, such as the clearance between cutter heads, thearrange of bent blade, grass removing angle and setting angle.

本文通过上述的试验和分析，给出了刀盘间距、机器前进速度以及刀滚旋转速度这三个因素在满足作业要求(覆盖率、埋草深度、碎土率)的前提下，降低功耗的最优组合方案，为进一步进行整机参数优化设计提供了重要的理论依据。

Sb can combine with Cu and P to form a low melting point compound which lowers the melting point of binary Cu-8P eutectic alloy by nearly 200℃. Bi and Cu can create compounds with low melting point(270℃) distributing at the boundaries and that is the reason why the melting point of (Cu-8P)-Bi is lower than that of binary Cu-8P eutectic alloy. The eutectic cluster can be refined with the addition of Fe, and that is the reason why the addition of Fe can decrease the melting point of Cu-8P alloy. Two means of decreasing the melting point of Cu-8P are found.

一定量的Sb与Cu， P形成低熔点相，从而大幅降低了Cu-8P合金的熔点，使其熔点降低近200℃；加入少量Bi后， Bi与Cu在共晶团晶界上形成熔点为270℃左右的低熔点化合物，且Bi的加入明显细化Cu-8P合金共晶团，从而使Cu-8P合金的熔点降低；加入Fe能明显细化Cu-8P合金的共晶团，使层片间距由8μm减为2μm以下，并使共晶团由层片状向短棒状转变，虽然Fe与Cu形成熔点为806℃的高温相，但Fe的细化作用使得Cu-8P合金的熔点降低，但降低幅度不大。

Measuring light wavelength with biprism interference is a very important experiment in the research and teaching of basic physics, the key to which is the distance measurement of the two virtual images.

用双棱镜干涉测量光波波长是基础物理研究和教学中非常重要的一个实验，该实验的关键环节是测量两虚相干光源间的距离，大多数实验教科书中大都采用二次成像法测量两虚相干光源的间距。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。