长方体

There are two modeling methods used in this research area, that is analytical method and numerical method. Analytical method can be used to analyze the sound pressure within enclosures, and to analyze the control mechanisms theoretically, however it can be used for regular cuboids only. Numerical modeling method can manage enclosures with arbitrary boundaries, nevertheless, the results obtained using this method are dispersed sound pressure. It is hard to conduct real time control with this method. The two modeling methods have their own inherent defects.

对于封闭空间的结构声辐射，目前有解析建模和数值建模两种建模方法，解析建模方法可以从理论上对系统进行分析，探讨消声机理，但它只适用于长方体等规则封闭空间；数值建模方法不受空间边界形状的限制，得到的是空间声压的离散结果，难以用于实时控制，两种方法都存在着局限性。

Let z be the height of the rectangular block.

设z 是长方体的高度。

The sightline control strategy for bad measure precision is developed, and the control methods for vertical direction, approach direction and station keeping are presented.(2)The safe approach velocities are investigated for cuboid, sphere and cone keep out zone.(3)The design method for optimal trajectory under safety constraint is developed. The cone and cuboid keep out zone can be described using line constraint, and then optimal trajectory design can be translated to line programming problem under line constraint.(4) The design strategy of collision avoidance maneuver is discussed, and the collision avoidance scheme is analyzed for V-bar and R-bar approach.The control and trajectory safety in departure phase are investigated.

1提出了测量误差较大时平移靠拢段的视线控制策略，给出了横向、纵向和悬停的控制方法；(2)针对长方体禁区、球形禁区和锥形禁区三种禁区形式，研究了V-bar逼近和任意方向逼近的纵向安全速度计算问题；(3)提出了安全约束下的最优轨迹设计方法，将冲量和有限推力作用下的最优轨迹设计问题转化为线性规划问题，并给出了将锥形和方形安全区域约束转化为标准线性约束的公式；(4)探讨了紧急避撞机动的设计策略，分析了V-bar和R-bar接近的紧急避撞机动方案。

Considering the skin effect and skin depth, a thin wall model and a thick wall model are derived creatively with different frequencies of discharge currents, which are used to study the relation between the spark location and the potential difference for a cuboid electrode.

本文从放电电流为任意函数入手，阐述了电极电位差法的检测原理，首次利用傅立叶级数推导了电位差与放电时间的关系，证明了放电电流为阶跃函数时，电位差与放电时间成指数关系；当放电电流中含有高频振荡时，电位差与放电时间的关系为指数曲线上叠加相移后的高频振荡；根据放电电流频率的不同，考虑到趋肤效应和趋肤深度，首创了薄壁模型和厚壁模型，研究了长方体电极下表面二维放电点位置与电位差的关系。

Next,by the use of the method on anisotropy subdivision in [8],we have proved the properly advanced element satisfy the feature of anisotropy for arbitrary convex cuboid subdivision in 3-dimension space and the error estimate is obtained.

接着，运用文献[8]中关于讨论各向异性的方法，我们证明了此单元在适当的改进之后，对长方体剖分满足各向异性特征，并且给出了相应的误差估计。

In the exterior of constant F60R is basic the straight edition modelling that is a cuboid, because be feeling screen design, accordingly it has lateral only key of two slip control---HOLD and switch.

中恒F60R的外观基本是一个长方体的直版造型，由于是触摸屏设计，因此它只有侧面的两个滑动控制键---HOLD和开关。

For the combustion chamber, the predicted results of pure radiative heat transfer were in good agreement with those of the zone method, while the SHF model gave relatively large deviations.

长方体空间的计算结果表明：DO模型的纯辐射传热预报结果比六热流模型准确，与计算精确的区域法的计算结果吻合较好，而SHF模型的预报结果却有较大的误差。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。