镀

In order to improve the efficiency of heat absorption by the tiny amount of adhesive used for micro optics packaging, we pre-process the components to be bonded, by first polishing the bonding surfaces and then depositing a very thin layer of metalized film on them.

为了改进微光学包装中微量粘合剂的热吸收率，我们先将接合面抛光，再镀上金属薄层。这样一来，微波能量将被镀层快速吸收。

The products are made of iron and copper materials, and they have two types of surface: One is chrome-plated, and the other is sandblasted and nickel-plated.

公司拥有&英雄&、&博士&、&凯达&等著名品牌；产品材质有铁质、铜质等；表面处理主要有镀铬和喷砂镀镍两种类型。

The complex plating-sulfurizing process which fitted multi-arc ion plating together with low temperature ion sulfurizing,was utilized to prepare the MoS_2 solid lubrication film on the surface of 45 steel.

采用多弧离子镀及低温离子渗硫相结合的复合镀渗工艺，在 4 5钢基体上制备了二硫化钼固体润滑薄膜。

Corrosion resistance of the deposits in simulated vulcanized gases was measured, and effect of thermal treatment on corrosion resistance of the.

研究了镀层在模拟硫化气氛中的耐蚀性及热处理对镀层耐蚀性的影响。

Process and mechanism of electrodeposited Zn-Fe-Si02 composite coatings were studied, including some contents as follow: Potential-pH plots of Zn-H2O and Fe-H2O systems were drawn, and the thermomechanical analysis was made. Results showed that the region of zinc and iron's codeposition was wide, which provided theoretic basis for electrodepositing Zn-Fe alloy. But the balance potential of zinc was greatly different from iron's, so in order to make zinc and iron codepositing, some complexant must be added into electroplating solution.

本文研究了电沉积Zn-Fe-SiO_2复合镀层的工艺和机理，主要包括以下几个方面：绘制了Zn-H-2O系和Pe-H_2O系的电位-pH图，并对其进行了热力学分析，结果表明，锌和铁发生共沉积的区域很大，这就对电沉积Zn-Fe合金的可能性提供了理论依据，但是锌和铁的平衡电位差别较大，所以，必须在镀液中添入一定量的配合剂才能使锌铁产生共沉积。

Results show that when ammonium molybdate is used as coloring agent and color the coating after it was nickel plating, different kinds of colors can be obtained by controlling the processing parameters with the unaltered wear and corrosion resistance.

结果表明：用铂酸铵作着色剂，并采用先镀镍，后着色的工艺，通过控制着色处理的工艺参数，可获得不同的色彩，并可保持镀层原有的耐磨、耐蚀性能。

First increased the built-up welding internal mixer special-purpose flinty antifriction metal in Gao Moqu, and in plates the 0.20mm thick hard chromium level with the sizing material contact active face, compared to domestic other company product coating accumulation one time, thus the service life obtains the big extension.

首先在高磨区增加了堆焊密炼机专用硬质耐磨合金，并在与胶料接触的工作表面均镀0.20mm厚硬铬层，比国内其他公司产品镀层增厚一倍，从而使用寿命得到大大延长。

Decorative gold-imitated barrel plating process for small article of zinc alloy die castings

某厂汽车零部件滚镀自动线采用锌铁合金新工艺取代了原氰化滚镀锌工艺。

The process, bath formula, coating quality and electrolyte performance of bright alkaline Zn-Al Alloy electroplating are studied.

研究了光亮碱性电镀Zn-Al合金的工艺配方、镀层质量和镀液性能。

Results show that only by selecting proper surfactant to disperse the nano-Al_2O_3 powders completely before adding in the plating bath can a fine composite coating with tiny Al_2O_3 well-distributed be obtained.

将纳米Al2O3应用于化学复合镀中，研究了表面活性剂对纳米Al2O3粉的分散状态和-Al2O3纳米微粒复合镀层组织形貌的影响。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。