镀

The thickness gauge for cladding material is install in brush plating power supply.

镀层厚度控制器是电刷镀设备必备的装置。

The effects of pulse parameters such as pulse width Ton, pulse interval Toff, pulse frequency f, pulse current density J on the morphology ,grain size , hardness, internal stress and orientation of coating , and coherence of coating to sucbstrate have been examined .

研究了脉冲电镀参数：脉冲宽度Ton ，脉冲间隔Toff，脉冲频率f，脉冲电流密度 J对镀层微观形貌、颗粒大小、硬度、与基体结合力的影响，分析了镀层内应力、择优取向与脉冲参数的关系。

We used ITO glass substrate and high purity（99.99%） titanium , put to use sputtering process, add to high purity O2 make it complete the best structure film and the thickness about 1400 . By way of 500℃ anneal could got a better anatase phase, this result could easy reaction with electrolyte to increase electron-transferred. Used as spin casting covering PR on ITO substrate, transferring patterns of array circular shapes on a mask to photography, used optimize temperature and time to hard bake. Finally used HCl to etching underexposed TiO2 area, and acetone to tripper top PR, make it to accomplish pillars shape TiO2 electrode.

本研究使用ITO玻璃基板为底材在以高纯度钛(99.99%)为靶材，利用溅镀方式通入纯氧使其行成高纯度TiO2镀於ITO基板上行成厚度约1400的薄膜，且经500℃高温烧结使其行成最强的锐钛矿结晶相，此晶相有利於与电解液反应进而增加电子的转移，提升太阳能电池最佳的效率，在以旋转涂布方式铺上光阻，以矩阵排列的圆孔光罩曝光、最佳的温度及时间来烘烤、显影后；使用盐酸以等向性湿蚀刻方式蚀刻未曝光之TiO2区域，最后利用鈵铜将最上层光阻去除，使其行成柱状TiO2的电极。

Through an introduction to the reaction principles and technical process of Ni-P chemical plating, and the investigation and analysis of anti-corrosive processing faults of Ni-P plating on the down-hole tool of present oilfields, some exact reasons are found out which causes the unstableness of anti-corrosive processing quality on down-hole tool s.

对Ni-P化学镀的反应原理和工艺流程作了介绍，对当前油田井下工具的Ni-P镀防腐处理故障情况进行了调查分析，找出了井下工具防腐处理质量不稳定的具体原因，并提出了提高施镀基面的精度要求等相应的改进对策。

Through an introduction to the reaction principles and technical process of Ni-P chemical plating, and the investigation and analysis of anti-corrosive processing faults of Ni-P plating on the down-hole tool of present oilfields, some exact reasons are found out which causes the unstableness of anti-corrosive processing quality on down-hole tools.

对Ni-P化学镀的反应原理和工艺流程作了介绍，对当前油田井下工具的 Ni-P镀防腐处理故障情况进行了调查分析，找出了井下工具防腐处理质量不稳定的具体原因，并提出了提高施镀基面的精度要求等相应的改进对策。

It can be used on stainless steel, steel, cast iron, vitreous enamel, glass, ceramics and most plastics, but not on aluminium, painted surfaces, zinc or tinned surfaces.

适用于炉灶、烤钩、烤架及其它重油污灶具，可用于不锈钢、钢材、铸铁、搪瓷、玻璃和大多数塑料，但不可用于铝、油漆、镀锌或镀锡制品上。

In this study, the ZnO thin films were deposited onto Si (100) substrate by ratio frequency sputtering with various RF power at 50, 100, 150, 200, and 300 W and the surface morphologies, crystalline structural, and nanomechanical properties of ZnO thin films were examined.

本研究利用射频磁控式溅镀(RF-sputtering)法於矽(100)基材上沉积高品质氧化锌薄膜，在实验中改变溅镀功率(50、100、150、200、以及300 W)来观察其对氧化锌薄膜表面形貌、晶格结构、及奈米机械性质的影响。

Welding technology and weldability of galvanized steel would be very important.

出不同的特性，随着镀层钢板在轿车工业的大量使用，掌握不同镀层汽车板的点焊工艺及性能就显得非常重要。

A method of determination for wetting Agent content in plating bath is described by surface tension or wetting angle technique. A simple and practical method is provided for plating technology and research.

本文介绍了用测定镀液表面张力或润湿角的方法来确定镀液中润湿剂的含量，为电镀工艺和电镀的研究工作提供了一种简便可行的物理化学测试方法。

To whiten by soaking in acid or by coating with tin.

在…上镀锡把浸在酸中或镀锡，使之变白

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。