镀

The paper analyses the heating efficiency and the combustor how to affect the output of galvanize d sheet.

介绍了镀锌工艺及退火炉的作用，着重分析了退火炉的传热效率和烧嘴能力对镀锌产量的影响。

Mechanism and optimum working conditions in mechanical galvanizing are discussed.

论述机械镀锌工艺的原理、最佳工艺条件及镀层的耐蚀性能，并与热镀锌和电镀锌作比较。

We report an experimental study of the glancing angle deposition and obliquely deposited Magnesium fluoride for vapor deposited thin films.

中文摘要本论文针对氟化镁材料以热蒸镀及斜向沈积技术制镀微观结构薄膜，以单一斜向沈积以及连续交错沈积法来制作非均向性的光学薄膜。

Within hours of arriving first timers soon usually stop mouthing trite phrases like 'but that is impossible' or 'surely they couldn't'. In go-getting ultra ambitious Dubai nothing is impossible and they surely could.

近十余年来，由于汽车业及家电业大量使用了镀锌钢板，并对镀锌钢板的性能提出了更高的要求，即除了应具有好的耐蚀性外，还应具有好的冲压成形性、焊接性和涂装性。

Hence, it is found that the carbon coating prepared at the film thickness of 88 nm is the best for hermetic optical fiber coating.

因此，在碳镀层厚度为88nm时，可得到最佳的碳密封镀层光纤的表面形态，并达到保护玻璃光纤的效果。

The analysis gets the result: the two methods both make out the heteromorphism InSb nanocrystals, which have different crystal lattices. There are few In and Sb elementary substance grains mixed in the samples and the ratio of two kinds of chemical elements nears to 1:1. The crystal structure of the particle which is gained in vacuum evaporation method is affected by the crystal structure of substrate surface and anneal, the size of grain is direct proportion to evaporation time.

分析得到结果表明：两种方法均制备出了多晶态的InSb纳米微粒，但晶格结构不同，样品中都混有少量的In和Sb单质颗粒，且两种元素的比均接近1：1；真空蒸镀法得到的微粒的晶态受基片表面晶格和退火的影响，颗粒的尺寸与蒸镀时间成正比；而惰性气体中蒸发法得到的微粒结晶过程与基片无关，颗粒的尺寸与惰性气体的种类和压强有关。

Electroless Co-Ni-P thin film as-deposited was amorphous possessing smooth surface. The film was crystallized after heat treatment at 300℃ for 1 hour, and the surface of film was composed of "taper humps". When the film was heated, phase of Co2P deposited from the solid solution and allotropic transformation took place from hexagonal close-packed system to face-centred cubic lattice.

摘 要：化学镀Co-Ni-P薄膜镀态下为非晶态结构，表面较为平整；经300℃×1h热处理，发生了晶化转变，表面由"圆锥峰"所构成；随加热温度的提高，镀层析出了Co2P相，并发生了由密排六方结构的α-Co向面心立方结构的β-Co的同素异构转变。

Its excellent slide properties and higher hardness were utilized so that the composite of Co－P－ PTFE has already possessed better tribological propetties with no heat treatment. The crystal analysis presents the composite of Co－P－PTFE has the structure of hexagonal system at plating state and its forming process has obviously the trend on a certain direction.

结构分析表明，Co－P－PTFE复合镀层镀态时即以六方密排晶体结构存在，它的形成过程有强烈的择优取向倾象，六方密排钴的(100)面平行于样品表面且衍射峰明显增强，热处理后的样品有部分固溶体形成。

HCD is a thin film deposition process based on hollow hot cathode ion-electron beam and ion plating techniques.

空心阴极放电离子镀技术，是在空心热阴极离子电子束技术和离子镀技术的基础上发展起来的一种薄膜沉积工艺。

The hardness and wear resistance of the RE-Ni-W-P-SiC composite coating increase with the rise of SiC and sodium tungstate concentrations in the bath respectively , while the hardness and wear resistance of the RE-Ni-W-P-SiC coating decrease with increasing sodium hypophosphate concentration in the bath.

随着镀液中次亚磷酸钠浓度的升高，镀层的硬度和耐磨性均降低。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。