镀

Surface hardened steel, surface heat treating and chemicaltreating materials, copper, aluminum alloy sheet, zinc layers,chrome layers, tin layers, bearing steel, cold and hard castingparts, etc.

表面淬火钢，材料表面热处理和化学处理，铜、铝合金等薄板，镀锌、镀铬、镀锡材料，轴承钢，冷硬铸件等。

Surface hardened steel, surface heat treating and chemical treating materials, copper, aluminum alloy sheet, zinc layers, chrome layers, tin layers, bearing steel, cold and hard CaSt ing parts, etc.

表面淬火钢，材料表面热处理和化学处理，铜、铝合金等薄板，镀锌、镀铬、镀锡材料，轴承钢，冷硬铸件等。

Surface hardened steel, surface heat treatingchemical treating materials, copper, aluminum alloy sheet, zinc layers, chrome layers, tin layers, bearing steel, coldhard casting parts, etc.

表面淬火钢，材料表面热处理和化学处理，铜、铝合金等薄板，镀锌、镀铬、镀锡材料，轴承钢，冷硬铸件等。

800 Square foot office building, the products are divided into: tents casing, hedging (including, zinc, nickel, chrome, spray), tent-iron gate support, disaster relief Peng iron frame, Beach chair steel pipes, etc. Complete specifications, members of 70 factories, eight technical staff.

办公楼1800个平方，产品主要分为：帐篷套管，套头（包括，镀锌，镀镍，镀铬，喷塑），帐蓬铁支架门杆，救灾蓬铁支架，沙滩椅钢管，等规格齐全，工厂员70名，技术人员8名。

By means of scanning auger microscopy and scanning electron microscopy , the composition of initial deposited surface, cross-section of deposit and surface after peeling off the EN coating was analyzed. The adhesion of EN deposit was evaluated with heat-quench and pull-off tests.

利用扫描俄歇显微镜和扫描电镜等手段分析了初始沉积表面、镀层横截面和镀层剥离表面的成分，采用热震和拉开试验定性测定了镀层的结合强度。

According to the graph of SEM, the grains on wood surface is main factor that affect the electric ability and the adhesive intensity of copper layer on wood, which could be resolved by increasing plating time.

从扫描电镜得出的图像来看，木材表面的纹理是影响镀铜层导电性以及表面附着强度的主要因素，可以通过适当增加施镀时间从而增加镀铜层在其内部的积聚量来解决。

To introduce the trial manufacture process of thick coat galvanized steel wire The galvanized steel wire for aluminium cable steel reinforced can be produced through adjusting process Quality of the product can get up to the grade C galvanized steel wire standard of ASTM?

介绍厚镀锌钢丝的试生产过程，通过工艺调整生产出了钢芯铝绞线用厚镀锌钢丝，产品质量满足ASTMB498—84C级镀锌钢丝要求，可替代进口并能出口。

A thin film of titanium carbide is obtained by vacuum evaporating oftitanium. With diffusion treatment, the existance of titanium carbide is identified by X-raydiffraction analysis. Quantatitive analysis is made by XPS to invetigate diffusion ofcarbon atom between diamond and titanium film.

用真空蒸镀法在金刚石表面镀覆Ti层，并经扩散处理使金刚石表面形成TiC膜，实现了金刚石表面的金属化。X射线衍射分析证实了TiC的存在，利用XPS定量分析验证了在金刚石表面碳原子与钛镀层之间的反应扩散模型。

Zinc coating was prepared using mechanical plating technology for the deposition of small amount tin salt.

采用少锡盐沉积机械镀锌工艺制备了机械镀锌的镀层。

On the basis of electroplating and immersion plating tin, and through large numbers of experiments, a new process of electroless plating tin in acid chloride bath solutions including SnCl2 2H2O, NaH2PO2 H2O, special complexing agent, additive agent, stabilizing agent and antioxidant, was established.

本文是在电镀锡、浸镀锡工艺配方的基础上，通过大量的试验，确立了一种以氯化亚锡、次亚磷酸钠和特定的络合剂、添加剂、稳定剂，抗氧化剂为基本镀液组成的酸性氯化物化学镀锡体系，成功地在铜上实现了锡的连续自催化沉积，获得了性能优异的半光亮银白色锡镀层。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。