锥形孔

Wedge mechanism was adopted in piercing die to achieve side piercing, and the positioning of taper pipe depended upon the conical surface of blanking die itself.

在冲孔模中选用了带有楔角的斜楔机构来实现侧冲，并利用冲裁凹模自身的锥形面实现了锥形管的定位。

A piston-shaped valve needle is contained in the bore in a longitudinally sliding fashion and has an essentially conical valve sealing surface by means of which the valve needle cooperates with the valve seat in order to control the at least one injection opening.

一个活塞状的阀针(5)可纵向移动地设置在孔(3)中并具有一个基本上锥形的阀密封面(7)，阀针(5)通过该阀密封面与阀座(9)相配合，以控制至少一个喷射口(11)。

A cone - shaped cavity in a steel in got,formed dur in g cool in g by escap in g gases.

铸件的缩孔，缩管铸件上的锥形孔，用来在冷却时排气用

Implement: Electro-hydraulic controlled implement, containing seven-hole lock-bars and tapered-pin locked swing arm, can be precisely positioned. The implement features long reach moldboard and superior rigidity.

作业装置：七孔连杆摆臂式作业装置由锥形销锁定，可有效消除运动间隙，具有运动范围大，机构刚性好的特点。

Flat and coned washers pre-assembled or loose, should be tested on a fixture having an oversize clearance hole so that a high tensile stress is induced to the washer.

组合螺栓和组合螺母上的平垫圈或锥形垫圈，或非组合件用的平垫圈或锥形垫圈，应在具有较大孔径的通孔的夹具上进行试验，从而使垫圈承受较大的拉伸应力。

In different conditions on fluidized state and stability of conical fluidized bed. The conlusions are: the conical angel of the conical fluidized bed is 20°, the fluidized state havesmall difference in conical distributor and distributor plate. The angle of conical bed increase,the fluidized state will have big difference. The angle is 60°and the conical as distributor, themass of fluidized is less, the most of material is the bottom of conical bed. The effect ofdistributor plate is much better than the conical distributor. Sawdust and rice hull can fluidize.The annular gap of conical distributor different, the angle of conical bed is same, the fluidizedquality of 10mm annular gap is better than the other conical distributors. The annular gap ismore wide, the conical bed have more slugging phenomenon and the pressure fluctuate is turnbig.In the experiment the flow of 2％and 4％distributor plates don\'t easy to control, becausethe pressure is very big and the pressure fluctuate of conical bed is too big.

在不同的条件下对锥形床的流化状态和稳定性进行了研究，结果得出：锥形床的锥角为20度时，分布锥和分布板的流化状态相差不明显，随着锥形床锥角的增大，分布锥和分布板的流化现象会出现明显的变化，锥形床锥角越大，分布锥的流化状态变化越明显，流化的的物料越少，大量物料都聚集在锥形床底部，而分布板在加料量少的情况下，能流化起来。10mm、15mm和20mm环隙分布锥在锥形床锥角相同条件下，10mm环隙分布锥的流化质量要好于其它两个分布锥，环隙越大越容易出现腾涌现象的产生，压降波动范围增大。2％、4％和6％开孔率分布板在本实验测定时，2％和4％开孔率分布板的流量不容易调节，同时产生的压降波动范围也很大，比较来说，6％开孔率分布板流化质量好些。

The fit clearance between cylinder shaft hole of wire coil and supporting shaft should be 0.1mm to 0.5mm.

在装线盘时，先要检查线盘与顶头之间的配合性能：通常线盘圆柱轴孔与顶头之间的配合间隙应在0.1mm～0.5mm之间：锥形轴孔与顶头的锥度偏差

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。

GB/T2624--936 and production in line with ISO5167 - 1 standard expenditure devices, including pressure Kok access standard orifice, the standard nozzle, the flange pressure from the standard orifice, the trail from pressure from the standard orifice, the length of the nozzle And Venturi tube and cultural Venturi nozzle, double orifice, eccentric orifice, missing a round orifice, cone-shaped entrance orifice, the first-orifice, Pitot Venturi tubes, nozzles, such as the speed of sound. OVAL Co., Ltd.

生产符合GB/T2624--936和ISO5167--1的标准节流装置；包括角接取压标准孔板、标准喷嘴、法兰取压标准孔板、径距取压标准孔板、长径喷嘴以及文丘里管和文丘里喷嘴、双重孔板、偏心孔板、圆缺孔板、锥形入口孔板、端头孔板、皮托文丘里管、音速喷嘴等。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。