锥形

In order to examine the effect of die gap on the wrinkling, the stamping of a tapered square cup with three different die gaps of 20 mm, 30 mm, and 50 mm was simulated. In each simulation, the die cavity opening is fixed at 200 mm, and the cup is drawn to the same height of 100 mm.

为了验证模具间隙对起皱的影响，模拟了一个在从20MM， 30MM和50MM不同模具间隙下的锥形方杯的冲压，在每次仿真中，模腔打开固定在200MM，杯形拉伸同样高度100MM。

It features the applications of a cone-type abrasive wheel without hole and a polishing head of abrasive sheel.

该装置的特点是使用无孔，锥形砂轮（如图3所示）和砂轮抛头（如图2所示）。

Check out Buck's selection of tapered and pocket sharpeners.

购买巴克精选的锥形磨刀器和口袋磨刀器。

Some of its conical teeth, vertebrae, and foot-long armor plates, or scutes, were first discovered by French paleontologist Albert-Felix de Lapparent.

他们的一些锥形牙齿、脊椎、长达一英尺的鳞甲首先被法国古生物学家阿尔贝－弗利克斯·德拉帕朗发现。

In particular, the special-shaped, tapered, spherical roof of the song panel, the board has a ladder leading development capability.

尤其对异形、锥形、球形屋面的曲面板、梯形板有着领先开发能力。

In the process of heating, reversing optical panel, the length of fiber almost proportional increased with distance from fiber to center of the plate; at the same time, the shape of fiber changed from cylindrical fibers to cone-shaped fiber that the diameter is change with the length.

光纤倒像器毛坯在这一加热、扭转过程中，纤维长度随着纤维到面板中心的距离近乎成比例增加；同时纤维的形状也由原来的柱形纤维变成直径随长度变化的锥形纤维。

First modeling, the dumplings are all over the triangle, four cone-shaped, pillow-shaped, Xiaobao pyramid, rod-shaped and so on.

先就造型而言，各地的粽子有三角、四角锥形、枕头形、小宝塔形、圆棒形等。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间的配合达到最佳状态，仍需大量的修整工作，如镗床的齿轮与齿条，若拆卸后齿轮的各项性能指标经检测尚能使用不需更换，而齿条磨损严重需更换，那么齿条及齿条安装面上的定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮的啮合间隙需达到技术要求的标准，此项工作需时约一天。

To cooperate with new and old parts: although standard zero, components, but in between interchangeable in assembly parts, and to make the optimal coordination between trim, still needs a lot of work, such as the gear and rack, boring if after removal of gear various performance indicators are used by detecting without the need to change, and to replace worn rack, rack and rack positioning pin hole on installation bolt holes and should be first, reoccupy hand crossed positioning drills and tapered reamer to match the drill and match hinge, and after the installation of new and old super-modulus gear mesh clearance to achieve technical standards, this work takes about one day.

。新，旧零部件重新配合过程：尽管标准零，部件间具有互换性，但在装配中，要使新旧零部件间旳配合达到最佳状态，仍需大量旳修整工作，如镗床旳齿轮与齿条，若拆卸后齿轮旳各项性能指标经检测尚能使用不需更换，而齿条磨损厉害需更换，那么齿条嘉逸条安装面上旳定位销孔和定位螺钉孔就需先划线定位，再用手电钻及锥形铰刀重新配钻和配铰，且新齿条安装完毕后与旧齿轮旳啮合间隙需达到技术要求旳标准，此项工作需时约─天。

Thread Snap Gages—Minimum Material: Pitch Diameter Cone Type and Vee and Thread Groove Diameter Type for inspecting the minimum-material limit pitch diameter.

螺纹卡规—最小材料：中径为锥形及V形及螺纹为凹槽形的直径，是用于检查最小材料极限的中径。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失