锥孔

If is the awl hole so long as trades the column the circular cone to be possible.

如果是锥孔只要把圆柱换圆锥就可以。

Used to have tapered bore bearing installed (with locking nut and lock washer) in a cylindrical outer surface of the shaft.

用于将有锥孔的轴承安装在有圆柱形外表面的轴上。

MS parameter: ion source: ESI; 50～800 m/z; ionization voltage: 3.0 kV; dry gas (N2) flow rate: 318 L/h; temp:150 ℃; emale cone voltage: 3.0 kV.

质谱条件：离子源：ESI；检出模式：正负离子二种形式；扫描范围：50～800m/z；电离电压：3.0kV；电喷雾接口干燥气(N2)流速318L/h；离子源温度150℃；锥孔电压30V。

Through analyzing the failure reason of double row tapered hole cylindrical roller bearing , the problem of bearing early failure which is due to unproper installment and usage during installing, debugging and trail running is solved.

通过对双列锥孔圆柱滚子轴承的失效原因进行分析，解决装机、调试和试车过程中经常出现的因安装使用不当造成轴承早期失效的问题。

In different conditions on fluidized state and stability of conical fluidized bed. The conlusions are: the conical angel of the conical fluidized bed is 20°, the fluidized state havesmall difference in conical distributor and distributor plate. The angle of conical bed increase,the fluidized state will have big difference. The angle is 60°and the conical as distributor, themass of fluidized is less, the most of material is the bottom of conical bed. The effect ofdistributor plate is much better than the conical distributor. Sawdust and rice hull can fluidize.The annular gap of conical distributor different, the angle of conical bed is same, the fluidizedquality of 10mm annular gap is better than the other conical distributors. The annular gap ismore wide, the conical bed have more slugging phenomenon and the pressure fluctuate is turnbig.In the experiment the flow of 2％and 4％distributor plates don\'t easy to control, becausethe pressure is very big and the pressure fluctuate of conical bed is too big.

在不同的条件下对锥形床的流化状态和稳定性进行了研究，结果得出：锥形床的锥角为20度时，分布锥和分布板的流化状态相差不明显，随着锥形床锥角的增大，分布锥和分布板的流化现象会出现明显的变化，锥形床锥角越大，分布锥的流化状态变化越明显，流化的的物料越少，大量物料都聚集在锥形床底部，而分布板在加料量少的情况下，能流化起来。10mm、15mm和20mm环隙分布锥在锥形床锥角相同条件下，10mm环隙分布锥的流化质量要好于其它两个分布锥，环隙越大越容易出现腾涌现象的产生，压降波动范围增大。2％、4％和6％开孔率分布板在本实验测定时，2％和4％开孔率分布板的流量不容易调节，同时产生的压降波动范围也很大，比较来说，6％开孔率分布板流化质量好些。

I am company mainly produces V-cone-pulley, 105 cone-pulley, Cone sets to connect disk, Gezhongfeibiao cone hole, straight-set pulley and connectivity.

目前我公司主要生产V型锥孔皮带轮，105锥孔皮带轮，锥套，连接盘，各种非标锥孔、直孔皮带轮和连接盘。

The appropriate structural sizes of the integral induction heater for preparing glass-coated Fe-based alloy microwires are the cone angle of the induction heater 120 to 130℃, height of the induction heater 12 to 14 mm, bottom hole height 2 to 4 mm, and bottom hole radius 3 to 4 mm.

在本文研究条件下，整体感应加热器的合理结构尺寸为：感应加热器锥角120~130°，感应加热器高度12~14mm，下锥孔高度2~4mm，下锥孔半径3~4mm。

When cutting tool roaled of spindle's hole by manipulator or other ways,the pull nail behind of knife hilts is sent to ahead of tension bar of spindle. When receives the clamps signal, the pressure oil is passed over the oil cylinder left cavity of the spindle rear part, the piston to the right migration ,tension bar also to right migration by small dish shape spring function, the stell ball of ahead circumference of the tension bar shrink the distribution diameter by spindle's cone hole's force, holds on the knife hilts and pull nail colsely.

当刀具由机械手或用其他方法装到主轴孔后，其刀柄后部的拉钉便被送到主轴内拉杆的前端，当接到夹紧信号时，将压力油通入主轴尾部的油缸左腔，活塞向右移动，拉杆在碟形弹簧的作用下也向右移动，其前端圆周上的钢球在主轴锥孔的逼迫下收缩分布直径，将刀柄拉钉紧紧拉住。

The heat pipe type superhard abrasive tool as one kind of abrasive tool includes one grinding head, one pipe union, one grinding head handle and one water jacket.

一种热管式超硬磨料磨具，属于磨料磨具，该磨具包括磨头(1)、管接头(2)、磨头柄(4)和水套(6)，其中磨头(1)中加工有一锥孔，作为热管工作腔。

Inner ring with tapered bore to the heart of the rolling bearings.

内圈有锥孔的向心滚动轴承。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了