锁紧螺母

Book equipment application in automobile, motorcycle, machinery foundation profession such as chain, fastener, bearing, box spanner, tool, special different type nut and flange surface nut, sides nut, welding nut, cover type nut , locknut, defence pine nut, pull hat nut, chain Luo pull, expansion gecko, independently axle gear, bicycle different type etc.

本设备应用于汽车、摩托车、机械基础行业（如链条、紧固件、轴承、套筒扳手、工具、特殊异型螺母、法兰面螺母、四方螺母、焊接螺母、盖型螺母、锁紧螺母、防松螺母、拉帽螺母、链条罗拉、膨胀壁虎、自行轴挡、自行车异型件等）等各类异型、复杂非标件的冷挤成型，适用范围广泛。

Smaller sizes use a lock nut with a locking washer, larger sizes use a nut with locking clip.

小尺寸轴承使用带锁紧垫圈的锁紧螺母大尺寸的轴承使用带锁紧卡箍的锁紧螺母。

Wheel bolts, nuts, lock nuts, weld nut, spring nut, washer, copper fasteners, stainless steel fasteners and other automotive fasteners.

车轮螺栓、螺母，锁紧螺母，焊接螺母，簧片螺母，垫圈，铜紧固件，不锈钢紧固件，其他汽车紧固件。

Press the axle end to the bottom, draw the brake wheel 2, and make it close to the tape of behind cover, revolve the nut 5 clockwise, make it touch with the brake wheel, continually revolve the nut for one to one and a half ring, lock the screw and wind window.

4顺轴下压转轴端部至底，提取制动轮2使其制动环与后端罩3锥面贴合，顺时针方向旋转锁紧螺母5，使其与制动轮端面接触，再将锁紧螺母继续按顺时方向转一圈至一圈半，上好锁紧螺钉和通风窗，调整完毕。

The relation among the bevel drive pinion bearing preloads, axial displacement and locknut screwing moment and the relation between the frictional moments were analyzed in this article.

该文分析了汽车主锥中圆锥滚子轴承的预紧力与轴向位移、压紧轴承的锁紧螺母拧紧力矩之间的关系，以及轴向位移量与启动摩擦力矩之间的内在联系，并研制出具有锁紧螺母预紧力矩和轴承启动摩擦力矩自动测量功能的主锥自动装配设备的控制系统。

Stainless steel hex nuts, nylon lock nuts, flange nuts, square weld nuts, square nuts, Cap nuts, etc.

不锈钢六角螺帽，尼龙自锁紧螺母，法兰面螺母，四方焊接螺母，四方螺母，盖形螺母等

Such as hexagonal nuts, lock nuts, flange nuts, nut and so thin.

如六角螺母、锁紧螺母、法兰面螺母、薄型螺母等。

Now our company is majoring in nuts series: rivet nuts, blind rivet, insert nuts,nylon locknuts, welded nuts, flange nuts and other kinds of auto standard parts.

上海锐拓五金现在主营紧固件系列中的螺母类产品：铆螺母，尼龙锁紧螺母，焊接螺母，法兰螺母，以及各类汽车标准件。

Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm. Repeat it for three release levers, their gaps should be the same, after that screw up the locking nuts, and check it to make sure.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍。

B. Unscrew the locking nuts on the release lever, meanwhile unscrew the adjusting nuts using a spanner, while doing that measure the gaps between the release levers and bearings by means of feeler gauge, until the gap reads 0.3-0.5mm.

b、旋松分离杠杆上的锁紧螺母，一面用扳手转动调节螺母，一面用厚薄规测量分离杠杆与分离轴承之间的间隙，直到间隙为0.3-0.5毫米为止，三只分离杠杆依次都调整好，再将锁紧螺母锁紧，然后复查一遍

No clear conclusions can be made about the predictie alidity of specific measures, they found, except for criteria for the underuse of drugs for cardioascular disease.

除了心血管病不合理用药标准外，对于特定评价方法的预测效度没有明确的结论。

The third and last is that almost all of them, being infinite in number, have been impostures, and by idle and crafty brains merely contrived and feigned after the event past.

第三、即最后一点是：几乎所有这些不胜枚举的预言都是欺人之谈，都是在事件过后由无聊而狡猾的脑筋推测与凭空捏造的。