铸

More real????time visual and haptic interaction with anatomical data ［J］.

适用于CT薄层扫描和三维重建肝脏管道系统的灌注和铸型的建模研究［J］。

More realtime visual and haptic interaction with anatomical data ［J］.

适用于CT薄层扫描和三维重建肝脏管道系统的灌注和铸型的建模研究［J］。

Corporation produces the round hole, the superfine pore and each kind of heteromorphous hole spurt the screw stock, to cast take the lead, the clean needle and the spinning module are suitable for the polyester fiber, the polypropylene fiber, the polyamide fiber, the ammonia black silk ribbon, the acrylic fibers, the adhesive-bonded cloth, compound spin, the PVC rug and so on.

公司所生产的圆孔、超细微孔和各种异形孔喷丝板、铸带头、清洁针及纺丝组件适用于涤纶、丙纶、锦纶、氨纶、晴纶、无纺布、复合纺、PVC地毯等。

The results show that the microstructure of as-cast Ti-45Al-7Nb-0·15B-0·4W becomes fineafter being HIPped and heat treated, and a more perfect lamellar microstructure is got. The temperature ofαphase

结果发现： Ti-45Al-7Nb-0·15B-0·4W的铸态组织经过热等静压和均匀化处理后，其晶团尺寸减小，层片组织更为完整； Ti-45Al-7Nb-0·15B-0·4W合金的α相转变温度为(1 290±5)℃； Ti-45Al-7Nb-0·15B-0·4W合金在超过1 295℃的温度进行热处理时，其显微组织由近层片

The used catalyzer is in as-cast or hydrogenization state and is prepared by mixing magnesium metal and Ti-V based alloy for catalyzer together and then ball-milling the mixture for 0.5-5 hours under hydrogen atmosphere of 1-50 atmosphere pressures.

所使用的催化剂为铸态或氢化态；制备的方法是将镁金属与作为催化剂Ti-V基合金混合后，在氢气氛下球磨0.5-5小时，球磨时所用的氢压为1-50大气压。

Skin ; Thcnar and Hypothenar ; Microvcssel casts ; Scanning electron microscopy

皮肤；鱼际和小鱼际；微血管铸型；扫描电镜

Using two fresh upper limbs of adult, the ABS casts of the fine vasculature about the skin, superficial and deep fascia of thenar and hypothenar were studied by scanning electron microscopy.

本文用2侧成人新鲜尸体上肢，经肱动脉灌注ABS丁酮溶液，制成铸型样品，喷镀金膜。在扫描电镜下，观察了手鱼际和小鱼际皮肤及浅、深筋膜微细血管的立体构筑。

Using JDM-30 strain gauge measurement and 4192A impedometer, effect of magnetization field and stress on the magnetostrictive properties d33, k33 and μ of the Fe83Ga17 alloy are measured.

采用真空感应熔炼法制备出铸态Fe83Ga17合金，用定向凝固的方法制备出取向多晶Fe83Ga17合金，使用JDM-30型磁致伸缩参数自动测量仪和4192A型阻抗分析仪，研究了磁化场和预压力对取向多晶Fe83Ga17合金磁致伸缩性能参数d33、k33及μ的影响。

Cast glass is an organic process, hand crafted and imperfected by nature, so each piece produced is unique.

压铸玻璃是一个有机的过程，通过手工制造，带有天然瑕疵，也正因如此，每一片都是独一无二的。

In this paper ,the possibility and necessity of impling hot delivery and hot charging to continuous casting billet in Lingang are discussed, and the technical scheme of hot delivery and hot charging to continuous casting billet are put forward.

探讨了在山西新临钢钢铁有限公司实现连铸坯热送热装工艺的必要性和可能性，提出了实现热送热装工艺的技术方案，并指出了推广实施热送热装技术应重视的几项工作。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。