铸

The pleural superficial blood vessels were smooth, while the constrictions of smooth muscle cells and round imprints of endothelial nuclei occurred on the surface of the subpleural and parenchymal arteriole and venule.

肺胸膜面浅层微血管的铸型表面光滑，胸膜下和肺实质内微动脉和微静脉的铸型表面可见平滑肌细胞形成的缩窄，以及圆形内皮细胞核的压痕。

Preparation of poly(vinylidene fluoride-co-hexafluoro propylene)-based symmetric microporous membranes by a dry/wet phase inversion method ;2. PES-C ultrafiltration membranes were prepared by phase inversion method using dimethylacetamide as solvent and EE as additive.

通过改变铸膜液中添加剂乙醚的含量，采用相转化法在平板刮膜机上制备了一系列超滤膜，考察了添加剂乙醚含量对铸膜液黏度、凝胶速度、膜性能和结构的影响，研究了PES-C/DMAc体系中添加剂乙醚作用的规律。

In recent years, with the advanced requirements for speedup and heavy load from rail transport, the advanced requirements for the property of supporting pedestal have been proposed. The inherent defectivenesses which include the low mechanical property, low fatigue ductility and low shock resistance of cast-steel product, and the avoidless gas cavity, shrinkage porosity, inclusion, crack, etc in cast-steel product, existed in the product of Cast-steel supporting pedestal, have threatened the high speed and safe running of railroad.

近年来，随着铁路运输对重载、高速要求的提高，对关键部件支撑座的性能要求也在提高，铸钢支撑座产品存在的固有缺陷(铸钢件本身的机械性能、疲劳韧性、抗冲击性能都不高，铸件产品无法避免地存在气孔、缩松、夹杂、裂纹等)对铁路高速安全运行已构成威胁。

The results show that as for the as-cast castings, eutectic Si particles are characterized as fibrous or long acicular shape as well as in homogenous distribution, and the impact absorbed energy varies from 1.17 to 2.35J. After T6 heat treatment, the eutectic Si particles become small granular or short bacilliform, and the aspect ratio and area fraction of Si particles decrease evidently. The energy of the T6-treated castings is 1.45-3.80 J, which is higher than that of the as-cast castings. Furthermore, the fracture mechanisms of different regions in the castings were analyzed and discussed.

结果表明：铸态下共晶Si粒子大多为纤维状或长针状，呈不均匀的网状分布，冲击吸收功在1.17~2.35J的范围内变化后；经T6热处理后，团簇状Al-Si共品相明显减少，共晶Si粒子呈现出粒状或短棒状，且细小均匀，Si粒子的长宽比和面积分数都有显著降低，冲击吸收功在1.45~3.80J的范围内变化，比铸态有明显提高。

After T6 heat treatment, the eutectic Si particles become small granular or short bacilliform, and the aspect ratio and area fraction of Si particles decrease evidently. The energy of the T6-treated castings is 1.453.80 J, which is higher than that of the as-cast castings. Furthermore, the fracture mechanisms of different regions in the castings were analyzed and discussed.

结果表明：铸态下共晶Si粒子大多为纤维状或长针状，呈不均匀的网状分布，冲击吸收功在1.17~2.35 J的范围内变化后；经T6热处理后，团簇状Al-Si共晶相明显减少，共晶Si粒子呈现出粒状或短棒状，且细小均匀，Si粒子的长宽比和面积分数都有显著降低，冲击吸收功在1.45~3.80 J的范围内变化，比铸态有明显提高。

It was found that the phase separation behavior of PPESK, ie., PPESK/NMP/H_2O and PPESK/NMP/NSA, all agree with the LCP correlation. The binodal lines of the three systems were calculated according LCP correlation. Therefore, the maximum content of NSA in the casting solution can be calculated according to the binodal lines of the system, which is a scientific solution for the establishment for the composition of casting solution.

实验结果表明LCP关系可以用于描述PPESK／NMP／H_2O和PPESK／NMP／NSA三元体系在相分离时的浊点组成，并根据LCP关系外推计算三元体系的双节线，由此可得铸膜液体系中非溶剂添加剂的上限含量，为PPESK铸膜液体系组成的构建提供了可靠的科学依据。

And under it was the similitude of oxen, which did compass it round about: ten in a cubit, compassing the sea round about.

3海周围有野瓜的样式，每肘十瓜，共有两行，是铸海的时候铸上的

And under the brim of it round about there were knops compassing it, ten in a cubit, compassing the sea round about: the knops were cast in two rows, when it was cast.

7：24 在海边之下，周围有野瓜的样式。每肘十瓜，共有两行，是铸海的时候铸上的。

In Pattern less casting manufacturing technology by using the disperse/cumuli prototyping principle of rapid manufacturing and resin sand moulding material, the three dimensional CAD model is stratified, sliced, the information of different high section are obtained, then these section are scaned, jet solidify, the resin sand prototyping or casting model is direct obtained.

无模铸型制造技术是以树脂砂为成型材料，利用快速成型技术的离散／堆积成型原理，对三维CAD实体模型进行分层切片处理，得到不同高度截面层的信息，采用截面扫描、喷射固化工艺，直接获得树脂砂铸型或铸造模具的一种方法。

The deciduate casting mould agent casting mould drawing of patterns agent adopt high grade material to compound but is accomplished, have volatilizing speed is quick , efficient, spread brush repetition usage many times , do not glue a model.

铸型脱模剂铸型脱模剂采用优质材料配制而成，具有挥发速度快、效率高，涂刷一次可重复使用多次，不粘模。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了