铰接的

Trough calculation, it is obviously reasonable to ignore the effect of joint bending stiffness and consider it as a hinge joint in calculation.

通过比较可知，在计算中忽略节点抗弯性能对结构的影响，把节点看成铰接是合理的，而忽略节点局部平动刚度对结构的影响，把节点看成理想铰接却引起了较大的误差。

The research is mainly focus ed on using law of energy through formula deduction to separately rough estimate the relation of cable force and frequency with reckon ing in the influence of cable's deadweight under three circumstances of hinge j oints in two sides; hinge joint in one side, fixed joint.

用能量法通过公式推导分别估算出在索两端铰接、一端铰接一端固结与两端固接三种情况下计入自重影响的索力与频率的关系。

And the inverse result of kinematics for the shield hinge equipment is obtained and one-degree inverse coefficient matrix of the impact, two-degree inverse coefficient matrix of the impact and the expression of velocity, acceleration for every component are calculated, all of these lay the foundation for the following kinetics of the shield hinge equipment.

研究盾构铰接装置的能控性问题，讨论铰接液压缸的驱动力对切口环上末端力的控制能力，通过盾构前体切口环的末端力能控性，理论证明盾构铰接装置在土层中工作时切口环的可行运动与不可行运动，并得到可行运动的运动特性曲线。

Related to foreign engineering design methods and experience, combined with similar domestic products and projects technology, the paper makes a summary of the design of articulated concrete block revetment and references to the designers.

因此，对铰接式护坡结构的设计计算尚无系统详细的规范加以指导，本文借鉴国外相关工程设计理念和经验，并结合国内类似产品与工程技术，对铰接式砌块护坡的设计计算方法进行系统地总结，为设计提供参考。

The characteristics and influencing factor on the bearing capacity,rotational stiffness and ultimate rotatability of steel frames with different semirigid joints are discussed,based on the experimental result.

完全刚接和理想铰接虽然使得分析和设计过程大大简化，但实际结构中的连接形式并非单纯刚接或理想铰接，应是介于二者之间的一种半刚性连接。

Because the ideal "rigid joint" and "hinged joint" are inexistent, the stiffness of any connection types is between ideal rigid joint and hinged joint.

因为理想的刚节点和铰接点是不存在的，任何连接形式的刚度都是介于理想刚接和完全铰接之间的。

Based on experimental results of unstiffened overlapped circular hollow section joints, the axial forces of experimental truss members connected with hinge joints, semi hinge joints or rigid joints, are calculated by the finite element analysis model.

以平面K型圆钢管搭接节点的试验数据为基础，通过对试验桁架建立铰接、半铰接和刚接杆系有限元模型，计算受外荷载作用下试验桁架各杆件的轴力。

In this topic design food machinery uses the high-pressuredviscolizer, its principle of work is: Uses the electric motor afterthe level V belt transmission deceleration, leads crank revolving,the crank throw crank causes with in the crank hinge connecting rodimpetus piston cylinder piston to make the straight reciprocatingmain motion in the piston cylinder, thus the impetus levelhydraulic valve and two level of hydraulic valve function, producesthe strength attracts, the row of mix material, achieves the evenmix the goal.

本课题设计食品机械中用的高压均质机，它的工作原理是：采用电动机经一级三角带传动减速后，带动曲轴旋转，曲轴推动曲柄使与曲柄铰接的活塞杆带动活塞缸中的活塞在活塞缸中作往复直线运动，从而推动一级液压阀和二级液压阀的作用，产生的力吸、排混合的物质，达到均匀混合的目的。

To further improve the precision of sizable parallel 6-axis force platform with gemels the basis of present manufacture and calibration techniques, the paper adopts the sign function, and presents the friction model of platform with Stewart structure based on the screw theory and theory of influence coefficient.

在已有制造工艺及标定技术基础上，为进一步改善大型铰接并联六维测力平台的测量精度，本文基于螺旋理论和影响系数原理，引入符号函数建立了Stewart结构大型铰接六维测力平台的摩擦模型。

Wave is the rotor blades hinges on the hinge between the propeller blade hub, the hinge allows the blade perpendicular to the rotor plane up and down waving, in order to make it not have chatter and the shutdown will not touch the ground, usually limited to damping and compatible digital devices ...

挥舞铰是旋翼桨叶于桨桨毂之间的铰接，这个铰接允许桨叶垂直于旋翼平面上下挥舞，为了使之不会产生颤振及在停机时不会触及地面，通常都有阻尼及限位装置相配合。。。。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。